Difficulty

Difficult

Steps

20

Time Required

                          35 - 40 minutes            

Sections

8

  • Battery
  • 2 steps
  • Back Case
  • 4 steps
  • Front Case
  • 2 steps
  • Lens
  • 2 steps
  • Motherboard - First Half
  • 3 steps
  • LCD Screen
  • 3 steps
  • Flash Assembly
  • 2 steps
  • AV Port
  • 2 steps

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackSony Cyber-shot DSC-W55

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery               
  • Slide the battery cover in the direction the arrow points.
  • Pull the battery cover towards you.

Slide the battery cover in the direction the arrow points.

Pull the battery cover towards you.

1024

Step 2

  • Flick the blue switch for the battery to pop out.
  • Remove the battery from the camera.

Flick the blue switch for the battery to pop out.

Remove the battery from the camera.

Step 3

              Back Case               
  • Using the Phillips #00 Screwdriver, remove the two screws from the caution panel.
  • Remove that panel.
  • Careful for falling pieces.

Using the Phillips #00 Screwdriver, remove the two screws from the caution panel.

Remove that panel.

Careful for falling pieces.

Step 4

  • Remove the screw with a Phillips #00 screwdriver from the right side of the camera (with ‘3x optical zoom’ engraved on the side panel).
  • Remove that panel.

Remove the screw with a Phillips #00 screwdriver from the right side of the camera (with ‘3x optical zoom’ engraved on the side panel).

Step 5

  • Remove the screw using the Phillips #00 screwdriver from the bottom of the camera, closest to the back cover.

Remove the screw using the Phillips #00 screwdriver from the bottom of the camera, closest to the back cover.

Step 6

  • Gently remove the back cover.
  • It may be a bit stiff, so use some force to remove it. Proceed with caution.

Gently remove the back cover.

It may be a bit stiff, so use some force to remove it. Proceed with caution.

Step 7

              Front Case               
  • Remove the screw using a Phillips #00 screwdriver on the left side (where the “3x optical zoom” panel use to be).

Remove the screw using a Phillips #00 screwdriver on the left side (where the “3x optical zoom” panel use to be).

Step 8

  • Remove the small screw using a Phillips #00 screwdriver on the bottom of the camera attached to the front cover.
  • Gently remove the front cover.
  • Put a little force to pop off the case. Proceed with caution.

Remove the small screw using a Phillips #00 screwdriver on the bottom of the camera attached to the front cover.

Gently remove the front cover.

Put a little force to pop off the case. Proceed with caution.

Step 9

              Lens               
  • Flip the black secure locks off. Tweezers may be necessary.
  • Detach the two orange cables.

Flip the black secure locks off. Tweezers may be necessary.

Detach the two orange cables.

Step 10

  • Gently pull the lens container out of the camera.

Gently pull the lens container out of the camera.

Step 11

              Motherboard - First Half               
  • Remove the black screw using a Phillips #00 Screwdriver on the motherboard.

Remove the black screw using a Phillips #00 Screwdriver on the motherboard.

Step 12

  • Remove the two orange cables on the top of the motherboard with tweezers.
  • Lift the motherboard out of its slot.

Remove the two orange cables on the top of the motherboard with tweezers.

Lift the motherboard out of its slot.

Step 13

  • For the AV port, detach the bottom orange cable.
  • For the LCD screen, detach the top orange cable on the right side of the motherboard.
  • For the motherboard, detach all the orange cables.
  • Careful not to damage the red, white, and black wires when lifting the board.

For the AV port, detach the bottom orange cable.

For the LCD screen, detach the top orange cable on the right side of the motherboard.

For the motherboard, detach all the orange cables.

Careful not to damage the red, white, and black wires when lifting the board.

Step 14

              LCD Screen               
  • Verify the orange cables from the motherboard are removed from the LCD screen.
  • Lift the LCD screen off the hinge.

Verify the orange cables from the motherboard are removed from the LCD screen.

Lift the LCD screen off the hinge.

Step 15

  • Verify that the LCD screen is attached to the chip on the back on the camera.
  • Remove the dial from the back of the camera. It pops right off very easily.
  • Remove the screw using a Phillips #00 Screwdriver from the camera.

Verify that the LCD screen is attached to the chip on the back on the camera.

Remove the dial from the back of the camera. It pops right off very easily.

Remove the screw using a Phillips #00 Screwdriver from the camera.

Step 16

  • Remove the orange cable that is attached between the top of the camera and the chip. It should slide straight out with a little bit of force.
  • Remove the chip and the LCD screen now from the camera.
  • The chip may need a slight upward tug with a fingernail or tweezer.

Remove the orange cable that is attached between the top of the camera and the chip. It should slide straight out with a little bit of force.

Remove the chip and the LCD screen now from the camera.

The chip may need a slight upward tug with a fingernail or tweezer.

Step 17

              Flash Assembly               
  • Verify that the orange cables from the top piece are removed from the motherboard.
  • Remove the screw using a Phillips #00 Screwdriver on the upper part of the back side.
  • Pull the top off slowly and with caution. It is still slightly attached and may need a little force.

Verify that the orange cables from the top piece are removed from the motherboard.

Remove the screw using a Phillips #00 Screwdriver on the upper part of the back side.

Pull the top off slowly and with caution. It is still slightly attached and may need a little force.

Step 18

  • Slowly twist out the flash assembly.
  • It is attached to the hinge so a little force is necessary.

Slowly twist out the flash assembly.

It is attached to the hinge so a little force is necessary.

Step 19

              AV Port               
  • Remove the screw using a Phillips #00 Screwdriver connected to the AV port.
  • Flip the camera to its back, gently pull the bottom cover.

Remove the screw using a Phillips #00 Screwdriver connected to the AV port.

Flip the camera to its back, gently pull the bottom cover.

Step 20

  • Grab the circular top and pull it straight out.
  • The tripod socket and the AV port can be separated.

Grab the circular top and pull it straight out.

The tripod socket and the AV port can be separated.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 7 other contributors 

                    Eddie Lo                     

Member since: 10/11/2010

283 Reputation

                                      4 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges                           

Team

                       Cal Poly, Team 9-20, Regan Fall 2010                        

                                                  Member of Cal Poly, Team 9-20, Regan Fall 2010 



                    CPSU-REGAN-F10S9G20                     


                                            5 Members                     


                                            18 Guides authored