Sony Cyber Shot Dsc W570 Flash Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Case Cover
5 steps
LCD Screen
4 steps
Flash
2 steps

Flags

Missing Prerequisites

This guide is missing information on how to start the process. Make a prerequisite guide!

BackSony Cyber-shot DSC-W570
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Case Cover

Remove the two Phillips head, 2.93 mm long screws at the bottom of the camera.
Make sure the battery compartment door is in lock position.

Remove the two Phillips head, 2.93 mm long screws at the bottom of the camera.

Make sure the battery compartment door is in lock position.

1024

Step 2

Turn the camera sideways so the left side is fasning upwards, remove the two Phillips head, 2.93 mm screws.

Turn the camera sideways so the left side is fasning upwards, remove the two Phillips head, 2.93 mm screws.

Step 3

Now turn the device so the opposite side is fasning upwards and remove the last two Phillips head, 2.93 mm screws.

Now turn the device so the opposite side is fasning upwards and remove the last two Phillips head, 2.93 mm screws.

Step 4

To remove the front cover, use a plastic opening tool gently pry the top cover.
Then gently lift the cover off.

To remove the front cover, use a plastic opening tool gently pry the top cover.

Then gently lift the cover off.

Step 5

To remove the back case cover from the body.
First use a plastic opening tool gently pry along the side of the camera.
Then slowly and gently lift the cover off.

To remove the back case cover from the body.

First use a plastic opening tool gently pry along the side of the camera.

Then slowly and gently lift the cover off.

Step 6

              LCD Screen

These are the two cables connecting the LCD screen to the motherboard below the screen.

These are the two cables connecting the LCD screen to the motherboard below the screen.

Step 7

Remove the LCD screen from the side opppsite the battery terminals. Watch for the two cords mentioned in the previous step. These will still be connected.The side will flip up as shown in the next step.

Remove the LCD screen from the side opppsite the battery terminals. Watch for the two cords mentioned in the previous step. These will still be connected.The side will flip up as shown in the next step.

Step 8

Pull these two cords straight back to disconnect them from the respective housings. Caution: The housing do not need to be moved or adjusted in anyway. Do not pull the cords at an angle, it can destroy the cords and the housing. Pull Straight Back!

Pull these two cords straight back to disconnect them from the respective housings. Caution: The housing do not need to be moved or adjusted in anyway. Do not pull the cords at an angle, it can destroy the cords and the housing. Pull Straight Back!

Step 9

This is what the camera should look like after 2 cords and the screen have been removed. The lens cord is being held to the side for a clearer view.

This is what the camera should look like after 2 cords and the screen have been removed. The lens cord is being held to the side for a clearer view.

Step 10

              Flash

These are buttons for menu. Be sure to check that the flash settings are correct for your scene. Do not replace flash until settings are verified.

These are buttons for menu. Be sure to check that the flash settings are correct for your scene. Do not replace flash until settings are verified.

Step 11

Caution: Touching the capacitor wires may cause serious injury. Use a capacitor discharge probe to safely rid the capacitors of dangerous charges.
After camera is disassembled the capacitor will need to be removed. Ribbons are gently pulled away from connector.

Caution: Touching the capacitor wires may cause serious injury. Use a capacitor discharge probe to safely rid the capacitors of dangerous charges.

After camera is disassembled the capacitor will need to be removed. Ribbons are gently pulled away from connector.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Kenneth

Member since: 01/21/2015

174 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team 9-1, Brown Winter 2015                        

                                                  Member of USF Tampa, Team 9-1, Brown Winter 2015 



                    USFT-BROWN-W15S9G1                     


                                            5 Members                     


                                            10 Guides authored

Missing Prerequisites#

Introduction#

What you need#

Team#

Missing Prerequisites

Introduction

What you need

Team