Sony Cyber Shot Dsc Wx100 Lens Assembly Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          35 minutes

Sections

Battery
2 steps
Outer Casing
3 steps
Image Sensor
5 steps
Lens Assembly
2 steps

Flags

BackSony Cyber-shot DSC-WX100
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Open the flap indicated to allow access to the battery slot.
The gray switch indicated has to be moved to the right in order to release the flap.

Open the flap indicated to allow access to the battery slot.

The gray switch indicated has to be moved to the right in order to release the flap.

1024

Step 2

If the old battery is still in the slot, then make sure the camera is turned off prior to removal.
If there is a battery currently in the slot, remove by first pulling downwards on the blue component. This will allow you to remove the battery from the slot.

If the old battery is still in the slot, then make sure the camera is turned off prior to removal.

If there is a battery currently in the slot, remove by first pulling downwards on the blue component. This will allow you to remove the battery from the slot.

Step 3

              Outer Casing

Remove all of the 1mm screws using a Philips #000 Screwdriver.
Remover the rest of the screws (2mm) from the camera covers using a Phillips #000 Screwdriver.

Remove all of the 1mm screws using a Philips #000 Screwdriver.

Remover the rest of the screws (2mm) from the camera covers using a Phillips #000 Screwdriver.

Step 4

Use the plastic opening tool to gently remove the front and back plates of the camera.

Use the plastic opening tool to gently remove the front and back plates of the camera.

Step 5

Use a plastic opening tool to gently release the two indicated tabs.

Use a plastic opening tool to gently release the two indicated tabs.

Step 6

              Image Sensor

Pull up on the lower end of the plate. Lift it so that the plate is uninhibited by the indicated bump.
Pull away from the camera at the end of the metal plate with the blue circuits to then remove the plate from the rest of the camera.
For help with this step, refer to the video.

Pull up on the lower end of the plate. Lift it so that the plate is uninhibited by the indicated bump.

Pull away from the camera at the end of the metal plate with the blue circuits to then remove the plate from the rest of the camera.

For help with this step, refer to the video.

Step 7

Remove this screw (1mm) with the Phillips #000 Screwdriver.
Gently lift the LCD screen component from the metal plate.
Remove the metal plate that was underneath the LCD screen from the camera.

Remove this screw (1mm) with the Phillips #000 Screwdriver.

Gently lift the LCD screen component from the metal plate.

Remove the metal plate that was underneath the LCD screen from the camera.

Step 8

Peel back the copper sheet.
Unscrew the three marked screws (2mm) using a Phillips #000 Screwdriver.
Remove the panel attached by said screws.

Peel back the copper sheet.

Unscrew the three marked screws (2mm) using a Phillips #000 Screwdriver.

Remove the panel attached by said screws.

Step 9

Peel back both the copper sheet and the black tape underneath the panel to expose the connection port.

Peel back both the copper sheet and the black tape underneath the panel to expose the connection port.

Step 10

Use a plastic opening tool to pry the black bar upwards.
Pull the image sensor out after the black tab is released.

Use a plastic opening tool to pry the black bar upwards.

Pull the image sensor out after the black tab is released.

Step 11

              Lens Assembly

Peel back the black tape to reveal the connection port shown below.

Peel back the black tape to reveal the connection port shown below.

Step 12

Pry the black bar upwards with a plastic opening tool.
Remove the wire sheet from the connection port.

Pry the black bar upwards with a plastic opening tool.

Remove the wire sheet from the connection port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Matthew

Member since: 03/18/2015

583 Reputation

                                      4 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Michigan Tech, Team 1-9, Lauer Spring 2015                        

                                                  Member of Michigan Tech, Team 1-9, Lauer Spring 2015 



                    MTU-LAUER-S15S1G9                     


                                            2 Members                     


                                            6 Guides authored

Vinicius Lupas - Sep 5, 2017

could i also replace the lens of my wx220 using these instructions?

Introduction#

What you need#

Team#

Introduction

What you need

Team