Difficulty

Moderate

Steps

31

Time Required

                          1 - 2 hours

Sections

8

  • Middle Trim
  • 5 steps
  • L1 and R1 Buttons
  • 2 steps
  • Rear Case
  • 4 steps
  • Battery
  • 2 steps
  • Motherboard Removal
  • 10 steps
  • Light Guide
  • 3 steps
  • Midframe Removal
  • 3 steps
  • Button
  • 2 steps

Flags

0

  • BackDualSense Controller v1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Note: This guide is for DualSense controllers with an FCC ID ending in 1. Check the back of your controller to verify your model. If yours ends in A, there will be differences in the internal design.

What you need

Step 1

              Unclip the right end of the middle trim
  • Disconnect and power down your controller before you begin.
  • Insert an opening pick underneath the middle trim at the bottom-right corner of the controller to release the clips securing it to the case.

Disconnect and power down your controller before you begin.

Insert an opening pick underneath the middle trim at the bottom-right corner of the controller to release the clips securing it to the case.

1024

Step 2

              Unclip the lower-right edge of the middle trim
  • Slide the opening pick along the lower-right edge of the middle trim to release the clips securing it to the case.

Slide the opening pick along the lower-right edge of the middle trim to release the clips securing it to the case.

Step 3

              Unclip the left end of the middle trim
  • Insert an opening pick underneath the middle trim at the bottom-left corner of the controller to release the clips securing it to the case.

Insert an opening pick underneath the middle trim at the bottom-left corner of the controller to release the clips securing it to the case.

Step 4

              Unclip the lower-left edge of the middle trim
  • Slide the opening pick along the lower-left edge of the middle trim to release the clips securing it to the case.

Slide the opening pick along the lower-left edge of the middle trim to release the clips securing it to the case.

Step 5

              Remove the middle trim
  • Use your fingers to lift up the bottom edge of the middle trim to release the remaining clips.
  • Lift the middle trim over the joysticks to remove it.

Use your fingers to lift up the bottom edge of the middle trim to release the remaining clips.

Lift the middle trim over the joysticks to remove it.

Step 6

              Remove the L1 button
  • Insert the flat end of a spudger into the gap above the L1 button.
  • Cover the button with your thumb to prevent it from ejecting across the room.
  • Pry upward to remove the L1 button.

Insert the flat end of a spudger into the gap above the L1 button.

Cover the button with your thumb to prevent it from ejecting across the room.

Pry upward to remove the L1 button.

Step 7

              Remove the R1 button
  • Insert the flat end of a spudger into the gap above the R1 button.
  • Cover the button with your thumb to prevent it from ejecting across the room.
  • Pry upward to remove the R1 button.

Insert the flat end of a spudger into the gap above the R1 button.

Pry upward to remove the R1 button.

Step 8

              Remove the rear case
  • Use a Phillips screwdriver to remove the two 6.4 mm screws securing the bottom corners of the lower case.

Use a Phillips screwdriver to remove the two 6.4 mm screws securing the bottom corners of the lower case.

Step 9

  • Use a Phillips screwdriver to remove the two 6.4 mm screws behind the L1 and R1 buttons.

Use a Phillips screwdriver to remove the two 6.4 mm screws behind the L1 and R1 buttons.

Step 10

  • Use the pointed edge of a spudger to unclip the two clips on either side of the headset jack.

Use the pointed edge of a spudger to unclip the two clips on either side of the headset jack.

Step 11

  • Remove the rear case.

Remove the rear case.

Step 12

              Disconnect the battery
  • Use a pair of tweezers or your fingers to disconnect the battery from the motherboard.
  • Grip the connector, not the wires, when disconnecting.

Use a pair of tweezers or your fingers to disconnect the battery from the motherboard.

Grip the connector, not the wires, when disconnecting.

Step 13

              Remove the battery
  • Lift the battery straight out of the battery bracket.

Lift the battery straight out of the battery bracket.

Step 14

              Remove the lower microphone
  • Grab the lower microphone ribbon cable pull tab with your fingers or a pair of tweezers and disconnect it from the motherboard.

Grab the lower microphone ribbon cable pull tab with your fingers or a pair of tweezers and disconnect it from the motherboard.

Step 15

              Remove the battery bracket
  • Use a Phillips screwdriver to remove the 6.4 mm screw securing the battery bracket.

Use a Phillips screwdriver to remove the 6.4 mm screw securing the battery bracket.

Step 16

  • Lift the battery bracket out of the motherboard.

Lift the battery bracket out of the motherboard.

Step 17

              Disconnect the right trigger assembly
  • Grip the right trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers and pull up to disconnect it from the motherboard.
  • Do not completely remove the ribbon cable yet.

Grip the right trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers and pull up to disconnect it from the motherboard.

Do not completely remove the ribbon cable yet.

Step 18

  • Grip the right trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers, and pull up to disconnect it from the trigger assembly.
  • Remove the ribbon cable.

Grip the right trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers, and pull up to disconnect it from the trigger assembly.

Remove the ribbon cable.

Step 19

              Disconnect the left trigger assembly
  • Grip the left trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers and pull up to disconnect it from the motherboard.
  • Do not completely remove the ribbon cable yet.

Grip the left trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers and pull up to disconnect it from the motherboard.

Step 20

  • Grip the left trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers, and pull up to disconnect it from the trigger assembly.
  • Remove the ribbon cable.

Grip the left trigger assembly ribbon cable pull tab with a pair of tweezers or your fingers, and pull up to disconnect it from the trigger assembly.

Step 21

              Disconnect the upper microphone
  • Use a pair of tweezers or your fingers to grip the upper microphone ribbon cable pull tab, and pull up to disconnect it from the motherboard.

Use a pair of tweezers or your fingers to grip the upper microphone ribbon cable pull tab, and pull up to disconnect it from the motherboard.

Step 22

              Disconnect the touchpad
  • Use a pair of tweezers or your fingers to grip the touchpad ribbon cable pull tab, and pull it straight out of the motherboard connector.

Use a pair of tweezers or your fingers to grip the touchpad ribbon cable pull tab, and pull it straight out of the motherboard connector.

Step 23

              Lift out the motherboard
  • Carefully guide the joysticks through the front case and lift the motherboard out.
  • Do not completely remove the motherboard. There are four soldered wires tethering the motherboard to the vibrator motors.

Carefully guide the joysticks through the front case and lift the motherboard out.

Do not completely remove the motherboard. There are four soldered wires tethering the motherboard to the vibrator motors.

Step 24

              Remove the light guide
  • Use a Phillips screwdriver to remove the two 8.5 mm screws securing the light guide.

Use a Phillips screwdriver to remove the two 8.5 mm screws securing the light guide.

Step 25

  • Use a pair of tweezers or your fingers to remove the light guide bracket.

Use a pair of tweezers or your fingers to remove the light guide bracket.

Step 26

  • Use a pair of tweezers or your fingers to remove the light guide.

Use a pair of tweezers or your fingers to remove the light guide.

Step 27

              Remove the speaker
  • Use a pair of tweezers to remove the speaker from the midframe.
  • Be sure to reinstall the speaker in the correct orientation with the foam pad on the left side and the gold contact points on the right.

Use a pair of tweezers to remove the speaker from the midframe.

Be sure to reinstall the speaker in the correct orientation with the foam pad on the left side and the gold contact points on the right.

Step 28

              Remove the midframe
  • Use a Phillips screwdriver to remove the two 6.4 mm screws securing the midframe to the front case.

Use a Phillips screwdriver to remove the two 6.4 mm screws securing the midframe to the front case.

Step 29

  • Carefully lift the midframe and motherboard up and out of the front case.
  • Be careful not to strain the vibrator motor wires.
  • During reassembly, feed the touchpad’s ribbon cable back through its rectangular opening in the midframe.

Carefully lift the midframe and motherboard up and out of the front case.

Be careful not to strain the vibrator motor wires.

During reassembly, feed the touchpad’s ribbon cable back through its rectangular opening in the midframe.

Step 30

              Remove the conductive silicone rubber
  • Use a pair of tweezers or your fingers to remove the three conductive silicone rubber pads from the inside of the front case.
  • The buttons are resting loose in the front case.

Use a pair of tweezers or your fingers to remove the three conductive silicone rubber pads from the inside of the front case.

The buttons are resting loose in the front case.

Step 31

              Remove the buttons
  • Hold the front case close to the surface of your table and slowly turn the front case over to let the buttons fall out.

Hold the front case close to the surface of your table and slowly turn the front case over to let the buttons fall out.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                    Sam Omiotek

Member since: 02/25/2019

55,294 Reputation

                                      288 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Guide Team                        

                                                  Member of Guide Team 



                    Community                     


                                            10 Members                     


                                            9,216 Guides authored