Difficulty

Moderate

Steps

12

Time Required

Suggest a time??

Sections

2

  • Cover
  • 4 steps
  • Laser
  • 8 steps

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackSony DVP-FX730

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Cover
  • Remove the five exposed 7.9 mm screws using a Phillips screwdriver.
  • Punch through the warranty sticker with the spudger.
  • Remove the screw underneath with the Phillips screwdriver.

Remove the five exposed 7.9 mm screws using a Phillips screwdriver.

Punch through the warranty sticker with the spudger.

Remove the screw underneath with the Phillips screwdriver.

1024

Step 2

  • Remove the rubber feet using the spudger.
  • Remove the screws that were covered by the rubber feet.

Remove the rubber feet using the spudger.

Remove the screws that were covered by the rubber feet.

Step 3

  • Hold on to the corners of the cover and gently lift the cover.
  • The tray is still connected to the base with wires.

Hold on to the corners of the cover and gently lift the cover.

The tray is still connected to the base with wires.

Step 4

  • Gently remove the wires with tweezers by pulling up on the base they are attached to.

Gently remove the wires with tweezers by pulling up on the base they are attached to.

Step 5

              Laser
  • Remove the large connector.
  • Remove the small connector.

Remove the large connector.

Remove the small connector.

Step 6

  • Remove Philips screws with the #0 Philips Screwdriver.

Remove Philips screws with the #0 Philips Screwdriver.

Step 7

  • Lift up the black piece connected to the wires.
  • Lift gently because the ribbon cable is attached to the bottom.

Lift up the black piece connected to the wires.

Lift gently because the ribbon cable is attached to the bottom.

Step 8

  • Unlock the lock clip

Unlock the lock clip

Step 9

  • Remove the T6 screws with the T6 screwdriver.

Remove the T6 screws with the T6 screwdriver.

Step 10

  • Gently pull the rods out with tweezers.
  • Be sure the laser is out of the way so that the rods can be removed.

Gently pull the rods out with tweezers.

Be sure the laser is out of the way so that the rods can be removed.

Step 11

  • Pull laser off of the rods.
  • Be careful when removing the rods because a fragile metal piece may break.

Pull laser off of the rods.

Be careful when removing the rods because a fragile metal piece may break.

Step 12

  • The laser is now removed.

The laser is now removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 8 other contributors 


                    Oliver Woolsoncroft

Member since: 01/20/2012

75 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team 11-21, Maness Winter 2012                        

                                                  Member of Cal Poly, Team 11-21, Maness Winter 2012 



                    CPSU-MANESS-W12S11G21                     


                                            4 Members                     


                                            5 Guides authored

mnmmacd - Dec 31, 2014

Reply

where do I buy the lens?