Sony Gtk Xb5 Daughterboard Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

Top Casing
5 steps
Daughterboard
4 steps

Flags

BackSony GTK-XB5
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Top Casing

Before you begin, be sure to unplug the speaker.
First, remove the eight screws on the speaker’s back panel. These screws should be located on the top and bottom corners of the back, as well as along the sides.
Remove the 7.5 mm Phillips-head screws using a Phillips #1 screwdriver with a J sized head.

Before you begin, be sure to unplug the speaker.

First, remove the eight screws on the speaker’s back panel. These screws should be located on the top and bottom corners of the back, as well as along the sides.

Remove the 7.5 mm Phillips-head screws using a Phillips #1 screwdriver with a J sized head.

1024

Step 2

Next, remove 4 more 7.5 mm Phillips-head screws on the top part of the speaker (where the power buttons and extra BASS buttons are located). Two of the screws are located on the underside of the handle and are hidden beneath black rubber covers. Remove the covers and use a Phillips #1 screwdriver to unscrew the screws.
The remaining two 7.5 mm Phillips-head screws are located on the base of the indented section of the speaker, pictured here. They are also hidden beneath black rubber covers. Repeat same process in removing the screws.

Next, remove 4 more 7.5 mm Phillips-head screws on the top part of the speaker (where the power buttons and extra BASS buttons are located). Two of the screws are located on the underside of the handle and are hidden beneath black rubber covers. Remove the covers and use a Phillips #1 screwdriver to unscrew the screws.

The remaining two 7.5 mm Phillips-head screws are located on the base of the indented section of the speaker, pictured here. They are also hidden beneath black rubber covers. Repeat same process in removing the screws.

Step 3

Caution: Be careful not to touch the capacitor wires as you work. If possible, use a capacitor discharge probe to safely rid the capacitors of dangerous charges.
Gently lift up the entire top plastic section of the speaker. Do so slowly, the section is still connected to the circuitboard by a belt.
Gently remove the belt from its junction on the board, and after doing so the top plastic casing of the speaker will be fully detached.

Caution: Be careful not to touch the capacitor wires as you work. If possible, use a capacitor discharge probe to safely rid the capacitors of dangerous charges.

Gently lift up the entire top plastic section of the speaker. Do so slowly, the section is still connected to the circuitboard by a belt.

Gently remove the belt from its junction on the board, and after doing so the top plastic casing of the speaker will be fully detached.

Step 4

Additionally, the sides need to be taken apart. You will need to take out 4 additional 7.5 mm Phillips-head screws on either side. These screws are located beneath larger grey pads with adhesive on them at the side corners of your speaker.
Remove the pads slowly, as the adhesive makes them tougher to remove and you do not want to rip them.
Use an opening tool to help take out the side shell from the rest of the speaker.
This step can be difficult to perform and do not hesitate to use some force, there are no delicate components on the immediate underside of the side panel.

Additionally, the sides need to be taken apart. You will need to take out 4 additional 7.5 mm Phillips-head screws on either side. These screws are located beneath larger grey pads with adhesive on them at the side corners of your speaker.

Remove the pads slowly, as the adhesive makes them tougher to remove and you do not want to rip them.

Use an opening tool to help take out the side shell from the rest of the speaker.

This step can be difficult to perform and do not hesitate to use some force, there are no delicate components on the immediate underside of the side panel.

Step 5

The speaker should now be stripped of its basic shell except for the bottom and front panels.
You have now disassembled the top casing of your speaker and you are prepared to make replacements of components!

The speaker should now be stripped of its basic shell except for the bottom and front panels.

You have now disassembled the top casing of your speaker and you are prepared to make replacements of components!

Step 6

              Daughterboard

Find the gold-yellow daughterboard, located underneath the top plastic housing of the speaker.

Find the gold-yellow daughterboard, located underneath the top plastic housing of the speaker.

Step 7

Remove the belt connecting the daughterboard to the motherboard by gently removing the yellow clip from its housing on the motherboard.
The belt can only be disconnected from the motherboard side of the connection.

Remove the belt connecting the daughterboard to the motherboard by gently removing the yellow clip from its housing on the motherboard.

The belt can only be disconnected from the motherboard side of the connection.

Step 8

Remove the four 6.4mm phillips head screws located at each corner of the daughterboard with a Phillips head screwdriver.

Remove the four 6.4mm phillips head screws located at each corner of the daughterboard with a Phillips head screwdriver.

Step 9

Gently slide the entire daughterboard towards the frontside of the speaker, unhooking it from the prong that keeps it in place.
The daughterboard is free to be fully removed. You are now prepared to replace or make replacements components on the daughterboard!

Gently slide the entire daughterboard towards the frontside of the speaker, unhooking it from the prong that keeps it in place.

The daughterboard is free to be fully removed. You are now prepared to replace or make replacements components on the daughterboard!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors

                    Tim Meagher

Member since: 02/14/2017

432 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 9-3, Banghart Winter 2017                        

                                                  Member of Cal Poly, Team 9-3, Banghart Winter 2017 



                    CPSU-BANGHART-W17S9G3                     


                                            4 Members                     


                                            6 Guides authored

M/S Gaming - Dec 22, 2018

Hi there how can I buy this thing daughter board I need that can you pls help me

Introduction#

What you need#

Team#

Introduction

What you need

Team