Difficulty

Moderate

Steps

17

Time Required

                          10 minutes

Sections

1

  • Speaker
  • 17 steps

Flags

0

  • BackSony Handycam DCR-SR68

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Speaker
  • Remove battery before working on device.
  • Undo hand strap.
  • Get iFixit screwdriver and a JIOS Philips head bit.

Remove battery before working on device.

Undo hand strap.

Get iFixit screwdriver and a JIOS Philips head bit.

1024

Step 2

  • Place device on left side with lens facing right.
  • Using the screwdriver, unscrew the left middle screw.
  • Open the “DC IN” tab.
  • Second screw is revealed.
  • Unscrew this screw.

Place device on left side with lens facing right.

Using the screwdriver, unscrew the left middle screw.

Open the “DC IN” tab.

Second screw is revealed.

Unscrew this screw.

Step 3

  • Turn device onto it’s top with the lens facing right.
  • Unscrew the top left and top right screws.
  • Right side casing is now free.

Turn device onto it’s top with the lens facing right.

Unscrew the top left and top right screws.

Right side casing is now free.

Step 4

  • Remove the right side casing by pulling away.
  • HDD is now revealed.

Remove the right side casing by pulling away.

HDD is now revealed.

Step 5

  • Using your fingers, lift the HDD by it’s right end, pivoting on it’s left end.
  • HDD ribbon wire is now exposed.

Using your fingers, lift the HDD by it’s right end, pivoting on it’s left end.

HDD ribbon wire is now exposed.

Step 6

  • Using your fingers, pull the ribbon wire out of it’s socket.
  • HDD is now free from device.
  • Set HDD aside

Using your fingers, pull the ribbon wire out of it’s socket.

HDD is now free from device.

Set HDD aside

Step 7

  • Using your fingers, remove the A/V tab.

Using your fingers, remove the A/V tab.

Step 8

  • On the bottom of the device, unscrew the right and middle bottom 3mm Philips screws.
  • Remove panel.

On the bottom of the device, unscrew the right and middle bottom 3mm Philips screws.

Remove panel.

Step 9

  • Using the screwdriver, unscrew the top two black 3mm Philips screws.
  • Lift out the grey tray, being careful when feeding the large ribbon wire though the slot.

Using the screwdriver, unscrew the top two black 3mm Philips screws.

Lift out the grey tray, being careful when feeding the large ribbon wire though the slot.

Step 10

  • Using the black pointed spudger, carefully pop op the latch on the large ribbon wire’s port.
  • Set large ribbon wire aside.

Using the black pointed spudger, carefully pop op the latch on the large ribbon wire’s port.

Set large ribbon wire aside.

Step 11

  • Using the blunt tweezers, unplug the red and black wires.
  • Using the blunt tweezers, unplug the small ribbon wire.

Using the blunt tweezers, unplug the red and black wires.

Using the blunt tweezers, unplug the small ribbon wire.

Step 12

  • Unscrew the top 3 3mm Philips screws from right to left.

Unscrew the top 3 3mm Philips screws from right to left.

Step 13

  • On the back of the device, unscrew the top 3mm Philips screw.

On the back of the device, unscrew the top 3mm Philips screw.

Step 14

  • On the left side of the device, unscrew the top 2 3mm Philips screws.
  • The top of the device is now free.

On the left side of the device, unscrew the top 2 3mm Philips screws.

The top of the device is now free.

Step 15

  • Remove the top of the device by lifting it upwards.
  • Be careful of the wires becoming snagged on the frame.

Remove the top of the device by lifting it upwards.

Be careful of the wires becoming snagged on the frame.

Step 16

  • With the top of the device in hand, remove the 4 visible 3mm Philips screws.
  • Remove the frame by lifting away.

With the top of the device in hand, remove the 4 visible 3mm Philips screws.

Remove the frame by lifting away.

Step 17

  • The speaker is the object on the right with a ribbon wire connecting to it.
  • Remove the broken speaker with your fingers.
  • Replace with new speaker.

The speaker is the object on the right with a ribbon wire connecting to it.

Remove the broken speaker with your fingers.

Replace with new speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    alejandro zuniga

Member since: 01/06/2016

736 Reputation

                                      4 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Eastern Washington University, Team 2-5, Andersen Winter 2016                        

                                                  Member of Eastern Washington University, Team 2-5, Andersen Winter 2016 



                    EWU-ANDERSEN-W16S2G5                     


                                            5 Members                     


                                            12 Guides authored