Sony Srs X2 Inner Wiring Replacement Repair Guide

Difficulty

Moderate

Steps

7

Time Required

                          1 hour            

Sections

3

• Face Plate
• 4 steps
• Battery
• 2 steps
• Inner Wiring
• 1 step

Flags

2

Missed a Step

Oops! This guide is currently missing some important steps.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackSONY SRS-X2

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              Face Plate               

• Use the metal spudger to pry the face screen open. Pull away from the device to remove.

Use the metal spudger to pry the face screen open. Pull away from the device to remove.

1024

Step 2

• Remove seven, 27 mm long Phillips #1 screws.
• Remove three, 11mm long Phillips #1 screws.
• Remove four, 10 mm long Phillips#1 screws.

Remove seven, 27 mm long Phillips #1 screws.

Remove three, 11mm long Phillips #1 screws.

Remove four, 10 mm long Phillips#1 screws.

Step 3

• Before removing the host plate, face the feet of the speaker to you. The wiring allows for minimal access to the inner components.
• Use the spudger to remove the speaker host plate. Insert the metal tip in the seam between the host plate and the shell.
• Be very careful when pulling the speaker host plate (described in the next step) as there are wiring connected to the host plate. This wiring is soldered to the plate and to the shell of the device. The wires are flexible and you can still open the device as shown in the second picture.
• Center the spudger on the top of the device, this is furthest from the wiring, in wiggling the spudger under the plate, the plate should move up and out of the shell, you can finish lifting the plate away with your fingers.

Before removing the host plate, face the feet of the speaker to you. The wiring allows for minimal access to the inner components.

Use the spudger to remove the speaker host plate. Insert the metal tip in the seam between the host plate and the shell.

Be very careful when pulling the speaker host plate (described in the next step) as there are wiring connected to the host plate. This wiring is soldered to the plate and to the shell of the device. The wires are flexible and you can still open the device as shown in the second picture.

Center the spudger on the top of the device, this is furthest from the wiring, in wiggling the spudger under the plate, the plate should move up and out of the shell, you can finish lifting the plate away with your fingers.

Step 4

• Be gentle when using the opening tool, wiggle the opening tool on each side of the socket to be sure the plastic does not snap.
• Be careful not to damage the wires, pull from the plastic base to unplug.
• Unplug the power cable connector shown using the plastic opening tool. Wiggle the tool under the lip of the plug, the smaller area and odd angle means lifting up with the plastic tool in the setup shown.
• Unplug the power connector shown using the plastic opening tool lift from the front of the plug shown and move the opening tool to either side to get it all the way out of the socket.

Be gentle when using the opening tool, wiggle the opening tool on each side of the socket to be sure the plastic does not snap.

Be careful not to damage the wires, pull from the plastic base to unplug.

Unplug the power cable connector shown using the plastic opening tool. Wiggle the tool under the lip of the plug, the smaller area and odd angle means lifting up with the plastic tool in the setup shown.

Unplug the power connector shown using the plastic opening tool lift from the front of the plug shown and move the opening tool to either side to get it all the way out of the socket.

Step 5

              Battery               

• Remove the four, 11 mm, Phillips#1 screws on the battery cover plate.

Remove the four, 11 mm, Phillips#1 screws on the battery cover plate.

Step 6

• Remove the battery cover plate carefully then proceed to remove the battery.

Remove the battery cover plate carefully then proceed to remove the battery.

Step 7

              Inner Wiring               

• After desoldering the wire disconnecting it for replacement is a matter of unplugging the remaining connection.
• Make sure the wire has some time to cool before handling.

After desoldering the wire disconnecting it for replacement is a matter of unplugging the remaining connection.

Make sure the wire has some time to cool before handling.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Megan Berthiaume                     

Member since: 10/04/2016

484 Reputation

                                      3 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges                           

Team

                       USF Tampa, Team 3-3, Sullivan Fall 2016                        

                                                  Member of USF Tampa, Team 3-3, Sullivan Fall 2016 



                    USFT-SULLIVAN-F16S3G3                     


                                            4 Members                     


                                            6 Guides authored