Sony Srs X55 Input Board Replacement Repair Guide

Difficulty

Easy

Steps

13

Time Required

                          25 minutes            

Sections

1

• Input Board
• 13 steps

Flags

0

• BackSony SRS-X55

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Input Board               

• Locate the six 9 mm screws on the bottom of the SRS-X55 and remove them using a Phillips head #2 screwdriver.

Locate the six 9 mm screws on the bottom of the SRS-X55 and remove them using a Phillips head #2 screwdriver.

1024

Step 2

• Insert a plastic spudger at the seam of the bottom panel and remove it from the rest of the speaker.

Insert a plastic spudger at the seam of the bottom panel and remove it from the rest of the speaker.

Step 3

• Locate the battery plug and remove it using a pair of tweezers.

Locate the battery plug and remove it using a pair of tweezers.

Step 4

• Locate the two 3.5 mm screws on the bottom of the I/O board and remove them using a Phillips head #2 screwdriver.

Locate the two 3.5 mm screws on the bottom of the I/O board and remove them using a Phillips head #2 screwdriver.

Step 5

• Use a plastic spudger to remove the I/O board from the speaker body.

Use a plastic spudger to remove the I/O board from the speaker body.

Step 6

• Insert a plastic spudger into the seam of the metal speaker cover and pry it downward until it releases from the speaker body.

Insert a plastic spudger into the seam of the metal speaker cover and pry it downward until it releases from the speaker body.

Step 7

• Locate the eight 8.9 mm screws on the face of the speaker assembly and remove them using a Phillips head #2 screwdriver.

Locate the eight 8.9 mm screws on the face of the speaker assembly and remove them using a Phillips head #2 screwdriver.

Step 8

• Insert a plastic spudger underneath one of the tabs located on the front of the speaker assembly and gently raise the speaker assembly above the rest of the speaker.
• Continue to the next step before attempting to lift the speaker assembly from the rest of the speaker entirely to avoid damaging internal wires.

Insert a plastic spudger underneath one of the tabs located on the front of the speaker assembly and gently raise the speaker assembly above the rest of the speaker.

Continue to the next step before attempting to lift the speaker assembly from the rest of the speaker entirely to avoid damaging internal wires.

Step 9

• Locate the two wire connections as shown underneath of the speaker assembly and unplug them using a pair of tweezers.

Locate the two wire connections as shown underneath of the speaker assembly and unplug them using a pair of tweezers.

Step 10

• Locate the wire connecting the motherboard and the input board under the top panel of the speaker and remove it using a pair of tweezers.

Locate the wire connecting the motherboard and the input board under the top panel of the speaker and remove it using a pair of tweezers.

Step 11

• Insert a plastic spudger into the seam at the edge of the top panel and gently pry it away from the rest of the speaker.
• The spudger can be inserted laterally into the opening created by the spudger and slid along the top as shown to remove the panel in a single motion.

Insert a plastic spudger into the seam at the edge of the top panel and gently pry it away from the rest of the speaker.

The spudger can be inserted laterally into the opening created by the spudger and slid along the top as shown to remove the panel in a single motion.

Step 12

• Locate the three 4.5 mm screws on top of the speaker input board and remove them using a Phillips head #2 screwdriver.

Locate the three 4.5 mm screws on top of the speaker input board and remove them using a Phillips head #2 screwdriver.

Step 13

• Insert a plastic spudger underneath the edge of the input board and gently pry it away from the rest of the speaker.

Insert a plastic spudger underneath the edge of the input board and gently pry it away from the rest of the speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 

                    Chris Sparzo                     

Member since: 01/26/2017

351 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       IUPUI, Team 2-3, Baechle Spring 2017                        

                                                  Member of IUPUI, Team 2-3, Baechle Spring 2017 



                    IUPUI-BAECHLE-S17S2G3                     


                                            3 Members                     


                                            3 Guides authored                     

luc belair - Nov 15, 2017

Reply

Where I can find a new input board for my srs-x55??

prafulpu - Jun 19, 2021

Reply

I want to buy the sony input board.. can u pls help me on this