Difficulty

Moderate

Steps

10

Time Required

                          10 - 15 minutes

Sections

2

  • Battery
  • 4 steps
  • Display
  • 6 steps

Flags

0

  • BackSony Vaio Fit SVF13N1ASNS

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the following ten screws from the bottom case of the laptop:
  • Two 6.5mm Phillips #00 Phillips screws.
  • Four 8.95mm Phillips #00 screws.
  • Four 6.25mm Phillips #00 screws.
  • The screws may be hidden underneath a rubber foot that can be removed with a spudger.

Remove the following ten screws from the bottom case of the laptop:

Two 6.5mm Phillips #00 Phillips screws.

Four 8.95mm Phillips #00 screws.

Four 6.25mm Phillips #00 screws.

The screws may be hidden underneath a rubber foot that can be removed with a spudger.

1024

Step 2

  • Use a plastic opening tool to separate the bottom cover from the laptop.
  • Lift the lower cover and pull away from the laptop.

Use a plastic opening tool to separate the bottom cover from the laptop.

Lift the lower cover and pull away from the laptop.

Step 3

  • Remove the eight Phillips #00 screws from the battery:
  • Six 4.65mm screws.
  • Two 4.65mm screws.

Remove the eight Phillips #00 screws from the battery:

Six 4.65mm screws.

Two 4.65mm screws.

Step 4

  • Lift the battery up and pull it out of the laptop.

Lift the battery up and pull it out of the laptop.

Step 5

              Display
  • Open the laptop and rotate the screen to the back side.
  • Remove the eight 2.85mm Phillips #00 screws from the back of the screen.

Open the laptop and rotate the screen to the back side.

Remove the eight 2.85mm Phillips #00 screws from the back of the screen.

Step 6

  • Rotate the screen back and close the laptop.
  • Use a plastic opening tool to carefully pry up the back plastic case.
  • Remove the back plastic case by sliding it down and pulling upwards.

Rotate the screen back and close the laptop.

Use a plastic opening tool to carefully pry up the back plastic case.

Remove the back plastic case by sliding it down and pulling upwards.

Step 7

  • Remove the thirteen 2.85mm Phillips #00 screws from the screen.

Remove the thirteen 2.85mm Phillips #00 screws from the screen.

Step 8

  • Use a spudger to lift up the black latch on the ZIF connector.
  • Pull the display ribbon cable out of the ZIF connector.

Use a spudger to lift up the black latch on the ZIF connector.

Pull the display ribbon cable out of the ZIF connector.

Step 9

  • Remove the display cable peeling up the tape.
  • The display cable locking mechanism is attached to the tape.

Remove the display cable peeling up the tape.

The display cable locking mechanism is attached to the tape.

Step 10

  • Remove the display.

Remove the display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 5 other contributors 


                    Althea McDavid

Member since: 02/14/2018

842 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team S2-G4, Nance Spring 2018                        

                                                  Member of USF Tampa, Team S2-G4, Nance Spring 2018 



                    USFT-NANCE-S18S2G4                     


                                            4 Members                     


                                            11 Guides authored