Sony Vaio Vgn Fs640 Back Cover Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          3 - 5 minutes

Sections

Battery
3 steps
RAM Cover
2 steps
Hard Drive
2 steps
Back Cover
4 steps

Flags

BackSony Vaio VGN-FS640
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Lay the closed laptop on its screen so the bottom is facing towards you.

Lay the closed laptop on its screen so the bottom is facing towards you.

1024

Step 2

Push both latches towards the center of the battery.

Push both latches towards the center of the battery.

Step 3

Revome the battery by pushing it away from the laptop.
Set the battery away from the laptop.

Revome the battery by pushing it away from the laptop.

Set the battery away from the laptop.

Step 4

              RAM Cover

With the bottom of the laptop facing up, locate the RAM cover.
The RAM is covered by the panel with four columns of vents.
Locate the screw (Length: 4.8 mm) holding down the panel, which is near the edge of the laptop. Unscrew it with your phillips #0 screwdriver.

With the bottom of the laptop facing up, locate the RAM cover.

The RAM is covered by the panel with four columns of vents.

Locate the screw (Length: 4.8 mm) holding down the panel, which is near the edge of the laptop. Unscrew it with your phillips #0 screwdriver.

Step 5

Use your fingers to slide the cover away from the laptop. (It will only slide a few millimeters)
Once the panel is out of its locked position, it can be lifted out without any resistance.

Use your fingers to slide the cover away from the laptop. (It will only slide a few millimeters)

Once the panel is out of its locked position, it can be lifted out without any resistance.

Step 6

              Hard Drive

Locate and remove the screw (Length: 7.7mm) for the hard drive cover.
Slide the cover until it is free from the laptop case.
Lift the cover to remove.

Locate and remove the screw (Length: 7.7mm) for the hard drive cover.

Slide the cover until it is free from the laptop case.

Lift the cover to remove.

Step 7

Locate and remove the four screws (Length: 7.7mm) holding the Hard Drive tray in place.
Using the tab on the tray, slide the Hard Drive away from the main body of the laptop.
The Hard Drive should now be disconnected.
Lift the drive out with the tab on the tray.

Locate and remove the four screws (Length: 7.7mm) holding the Hard Drive tray in place.

Using the tab on the tray, slide the Hard Drive away from the main body of the laptop.

The Hard Drive should now be disconnected.

Lift the drive out with the tab on the tray.

Step 8

              Back Cover

Locate the screws highlighted here. There are 16 total.
Using a Phillips #0 screwdriver, remove the screws (Length: 6.8mm) and place them on a tray for later use.

Locate the screws highlighted here. There are 16 total.

Using a Phillips #0 screwdriver, remove the screws (Length: 6.8mm) and place them on a tray for later use.

Step 9

Before you proceed, make sure you pay special attention to the way the small plastic part that covers the radiator fins is held in place. You will need to know how it attaches when you reassemble the laptop.
You do not need to actually remove the part at this time. It is held in place by the rest of the back cover and will fall off when back cover is removed in the next step.

Before you proceed, make sure you pay special attention to the way the small plastic part that covers the radiator fins is held in place. You will need to know how it attaches when you reassemble the laptop.

You do not need to actually remove the part at this time. It is held in place by the rest of the back cover and will fall off when back cover is removed in the next step.

Step 10

After removing the screws, use your fingers to lift the back cover off the laptop.

After removing the screws, use your fingers to lift the back cover off the laptop.

Step 11

Remove the back cover and place it somewhere safe so you can locate it later.

Remove the back cover and place it somewhere safe so you can locate it later.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 5 other contributors

                    Kevin Lau

Member since: 04/10/2010

150 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 24-32, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 24-32, Regan Spring 2010 



                    CPSU-REGAN-S10S24G32                     


                                            4 Members                     


                                            16 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team