Difficulty
Moderate
Steps
11
Time Required
30 minutes
Sections
3
- Back Cover
- 4 steps
- Battery
- 4 steps
- Rear Camera
- 3 steps
Flags
0
BackSony Xperia M4 Aqua
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Place the phone face-down, and use a heat gun or hair dryer to evenly heat the back surface until to soften the adhesive.
Place the phone face-down, and use a heat gun or hair dryer to evenly heat the back surface until to soften the adhesive.
1024
Step 2
- Attach a suction cup to the back of the M4 Aqua by carefully pushing down on it near the top of the phone.
Attach a suction cup to the back of the M4 Aqua by carefully pushing down on it near the top of the phone.
Step 3
- While Pulling on the suction cup, slide a thin plastic spacer (guitar picks work well) between the back cover and the phone. Slide it around the edges to break the adhesive seal. Be careful, but don’t be afraid to use some force. You should hear a sticky breaking sound.
While Pulling on the suction cup, slide a thin plastic spacer (guitar picks work well) between the back cover and the phone. Slide it around the edges to break the adhesive seal. Be careful, but don’t be afraid to use some force. You should hear a sticky breaking sound.
Step 4
- Remove the back cover by pulling it from the chassis. it is flexible and can be bent, be careful.
Remove the back cover by pulling it from the chassis. it is flexible and can be bent, be careful.
Step 5
Battery
- Remove copper plated tape and any other securing adhesive with a nylon spudger. Remove carefully, as it has the potential or tear if too much force is used.
Remove copper plated tape and any other securing adhesive with a nylon spudger. Remove carefully, as it has the potential or tear if too much force is used.
Step 6
- Unhook the battery connector carefully. It is possible to damage the battery if too much force is used.
Unhook the battery connector carefully. It is possible to damage the battery if too much force is used.
Step 7
- Pry the battery from the phone with the nylon spudger. There is a small amount of adhesive underneath the battery, so a bit of force is required. The battery is malleable, so it is possible to dent the battery if too much force is applied in one spot.
Pry the battery from the phone with the nylon spudger. There is a small amount of adhesive underneath the battery, so a bit of force is required. The battery is malleable, so it is possible to dent the battery if too much force is applied in one spot.
Step 8
- Remove the battery once all of the adhesive is broken, and the connector is unplugged.
Remove the battery once all of the adhesive is broken, and the connector is unplugged.
Step 9
Rear Camera
- Remove the four hex head 3mm screws at each corner of the motherboard with a screwdriver.
Remove the four hex head 3mm screws at each corner of the motherboard with a screwdriver.
Step 10
- Remove three pieces of the securing bracket using tweezers
Remove three pieces of the securing bracket using tweezers
Step 11
- Detach the rear camera connector from the front of the motherboard.
- Remove the rear camera with your fingers or tweezers.
Detach the rear camera connector from the front of the motherboard.
Remove the rear camera with your fingers or tweezers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 6 other contributors
Sarah Wetzler
Member since: 02/10/2016
487 Reputation
2 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 4-5, Lacy Spring 2016
Member of USF Tampa, Team 4-5, Lacy Spring 2016
USFT-LACY-S16S4G5
3 Members
8 Guides authored
Faruk - Sep 29, 2016
Reply
Das ist kein Xperia Z3
Das ist eine Anleitung vom M4 Aqua
mivanchev - Jan 24, 2017
Reply
That’s the front camera. You have the front and rear camera mixed up!