Difficulty
Moderate
Steps
20
Time Required
15 - 20 minutes
Sections
3
- LCD Screen
- 5 steps
- Battery
- 4 steps
- Rear Camera
- 11 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackSony Xperia XZ2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
For this guide you will need a hair dryer, opening picks, angled tweezers, a spudger, and a Phillips #00 screwdriver.
What you need
Step 1
LCD Screen
- Weaken the glue that is keeping the screen in place by heating up the edges of the phone with a hair dryer or heat gun.
- The phone gets very hot and can hurt the user handling it.
Weaken the glue that is keeping the screen in place by heating up the edges of the phone with a hair dryer or heat gun.
The phone gets very hot and can hurt the user handling it.
1024
Step 2
- Scrape all the glue from the inside edges by inserting opening picks into the bottom edge of the phone and working your way around the edges.
- If the glue hardens and becomes difficult to move the plastic around the edges, reheat the phone.
Scrape all the glue from the inside edges by inserting opening picks into the bottom edge of the phone and working your way around the edges.
If the glue hardens and becomes difficult to move the plastic around the edges, reheat the phone.
Step 3
- Pry open the phone by inserting an opening pick under one of the edges and removing the screen.
- The screen is still attached by a connector, so do not pull the pieces apart.
Pry open the phone by inserting an opening pick under one of the edges and removing the screen.
The screen is still attached by a connector, so do not pull the pieces apart.
Step 4
- Remove the bracket covering the connector by grabbing one side of the bracket with angled tweezers and gently pulling it off.
Remove the bracket covering the connector by grabbing one side of the bracket with angled tweezers and gently pulling it off.
Step 5
- Gently remove the connector by using a spudger to pop it off.
Gently remove the connector by using a spudger to pop it off.
Step 6
Battery
- Take out the twelve 3.5mm screws using the Phillips #00 screwdriver.
- Remove the one 3 mm Phillips #00 screws.
- Remove the two 1mm Phillips #00 screws.
- Fifteen screws should be removed in total in this step. (Not all the screws are visible in the picture.)
Take out the twelve 3.5mm screws using the Phillips #00 screwdriver.
Remove the one 3 mm Phillips #00 screws.
Remove the two 1mm Phillips #00 screws.
Fifteen screws should be removed in total in this step. (Not all the screws are visible in the picture.)
Step 7
- Lift the metal screen shield out of the phone.
Lift the metal screen shield out of the phone.
Step 8
- Use the spudger to pry up the battery flex connector to pop the battery out.
Use the spudger to pry up the battery flex connector to pop the battery out.
Step 9
- Lift the battery out of the phone.
Lift the battery out of the phone.
Step 10
Rear Camera
- Pry off the flex connector with a spudger.
Pry off the flex connector with a spudger.
Step 11
- Take out the one 3mm screw on the motherboard with the Phillips #00 screwdriver.
Take out the one 3mm screw on the motherboard with the Phillips #00 screwdriver.
Step 12
- Using a spudger, remove the antenna connector.
Using a spudger, remove the antenna connector.
Step 13
- Gently lift the proximity sensor bracket by using a spudger.
Gently lift the proximity sensor bracket by using a spudger.
Step 14
- Remove the SIM card holder.
Remove the SIM card holder.
Step 15
- Pry off the flex connector using the spudger.
Pry off the flex connector using the spudger.
Step 16
- Use the spudger to lift the motherboard out of the phone.
Use the spudger to lift the motherboard out of the phone.
Step 17
- Disconnect the yellow connector by gently prying both sides of it using a spudger.
Disconnect the yellow connector by gently prying both sides of it using a spudger.
Step 18
- Disconnect the camera module from the motherboard by pulling the module up from the side using a spudger.
Disconnect the camera module from the motherboard by pulling the module up from the side using a spudger.
Step 19
- Remove the upper module by gently lifting it with a spudger.
Remove the upper module by gently lifting it with a spudger.
Step 20
- Gently lift up the rear camera by using a spudger under the rear camera.
Gently lift up the rear camera by using a spudger under the rear camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Dan Nguyen
Member since: 01/24/2019
326 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Cal Poly, Team S19-G5, White Winter 2019
Member of Cal Poly, Team S19-G5, White Winter 2019
CPSU-WHITE-W19S19G5
4 Members
10 Guides authored