Difficulty
Moderate
Steps
11
Time Required
5 - 10 minutes
Sections
1
- Battery
- 11 steps
Flags
0
BackSony Xperia Z Ultra
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use the small suction cup to lift the back panel:
- Press the small suction cup on to the middle of the back panel.
Use the small suction cup to lift the back panel:
Press the small suction cup on to the middle of the back panel.
1024
Step 2
- While holding the Sony Xperia Z ultra down with your left hand, slightly pull the small suction cup upwards to create a small opening between the back panel and the front panel.
- While continuing to pull the small suction cup upwards, insert the spudger in the small opening.
- Pry the front panel downwards with the spudger while continuing to pull the small suction cup upwards.
While holding the Sony Xperia Z ultra down with your left hand, slightly pull the small suction cup upwards to create a small opening between the back panel and the front panel.
While continuing to pull the small suction cup upwards, insert the spudger in the small opening.
Pry the front panel downwards with the spudger while continuing to pull the small suction cup upwards.
Step 3
- Remove the back panel by pulling the small suction cup upwards.
Remove the back panel by pulling the small suction cup upwards.
Step 4
- Remove the following six screws with a Phillips #000 screwdriver:
- five silver 2.1 mm screws
- one gold 3.1 mm screw
Remove the following six screws with a Phillips #000 screwdriver:
five silver 2.1 mm screws
one gold 3.1 mm screw
Step 5
- Pry the plastic motherboard shield open by placing the spudger under the shield and running it along the edges.
Pry the plastic motherboard shield open by placing the spudger under the shield and running it along the edges.
Step 6
- Use care to remove the motherboard shield, as it may break. The motherboard shield is made of a very thin plastic.
- Remove the motherboard shield by lifting the lower end upwards first.
Use care to remove the motherboard shield, as it may break. The motherboard shield is made of a very thin plastic.
Remove the motherboard shield by lifting the lower end upwards first.
Step 7
- Detach the battery connection cable by prying it upward with the spudger.
Detach the battery connection cable by prying it upward with the spudger.
Step 8
- Pry the upper end of the antenna upwards with the spudger.
Pry the upper end of the antenna upwards with the spudger.
Step 9
- Detach the antenna by pulling the upper end upwards and outwards.
Detach the antenna by pulling the upper end upwards and outwards.
Step 10
- Insert the spudger underneath the battery and run it back and forth to remove any adhesive.
Insert the spudger underneath the battery and run it back and forth to remove any adhesive.
Step 11
- Remove the battery from the phone.
Remove the battery from the phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
15 other people completed this guide.
Author
with 4 other contributors
Carlos
Member since: 10/01/2015
219 Reputation
1 Guide authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 4-6, Maness Fall 2015
Member of Cal Poly, Team 4-6, Maness Fall 2015
CPSU-MANESS-F15S4G6
4 Members
10 Guides authored
atilasilva - Jun 6, 2016
Reply
Does this fix change the waterproof efficiency?
Sven Decker - Jun 27, 2016
Hello atilasilva,
I guess so. Since you have to either replace the complete back cover or at least the glue line around the back cover I think the phone will not be completely waterproof again. It still may be solid splash proof.
Brandon Sisco - Jan 13, 2017
Reply
Battery available for $14.99 on eBay http://www.ebay.com/itm/112267192605
Kirill - Dec 30, 2019
Reply
Thanks a lot. This instruction really helped me to replace the battery!
David444 - Jan 31, 2020
Reply
I am about to follow your procedures to do a battery replacement. I have read your instructions, one question is if any need to use some glues to fix the back panel of the Sony Phone? From your instruction you did not mention the use of any glue at all, I am a bit concerned because at the moment my Sony phone both front and back panes are already loosen. I was told this is due to the old battery expanding.
Thanks for your help