Sony Xplod Cdx Mp30 Power Supply Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          30 minutes            

Sections

3

• Front Panel
• 1 step
• Main Panels
• 10 steps
• Power Supply
• 1 step

Flags

1

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

• BackSony Xplod CDX-MP30

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Front Panel               

• Press down the release button on the bottom left corner of the face plate.
• Then remove the face plate carefully.

Press down the release button on the bottom left corner of the face plate.

Then remove the face plate carefully.

1024

Step 2

              Main Panels               

• Using the Phillips #0 Screwdriver, unscrew the 3 screws (length - 7.5mm) on the front of the device.

Using the Phillips #0 Screwdriver, unscrew the 3 screws (length - 7.5mm) on the front of the device.

Step 3

• Using the Phillips #1 Screwdriver, unscrew the 2 thick screws (length - 7.69mm) located on both sides of the stereo.
• Remove side-metal plates gently.
• Use the Heavy-duty Spudger, insert the flat end under each of the black flaps indicated in the picture. Use leverage to pry and pop them loose.

Using the Phillips #1 Screwdriver, unscrew the 2 thick screws (length - 7.69mm) located on both sides of the stereo.

Remove side-metal plates gently.

Use the Heavy-duty Spudger, insert the flat end under each of the black flaps indicated in the picture. Use leverage to pry and pop them loose.

Step 4

• Remove the black front plate of the stereo.

Remove the black front plate of the stereo.

Step 5

• Using the Phillips #0 Screwdriver, unscrew the 1 gold screw (height - 7.47mm) on the top of the stereo.
• Lift off the top plate.

Using the Phillips #0 Screwdriver, unscrew the 1 gold screw (height - 7.47mm) on the top of the stereo.

Lift off the top plate.

Step 6

• Using the Phillips #0 Screwdriver, unscrew the 8 gold screws (length - 9.26mm), located on the back side of the stereo.
• Using the Phillips #0 Screwdriver, unscrew the 2 black screws (length - 13.27mm), also located on the back of the stereo.
• Using the Phillips #0 Screwdriver, unscrew the 1 gold screw (length - 9.3mm), located on the bottom of a hole as noted in pictures (2) and (3).

Using the Phillips #0 Screwdriver, unscrew the 8 gold screws (length - 9.26mm), located on the back side of the stereo.

Using the Phillips #0 Screwdriver, unscrew the 2 black screws (length - 13.27mm), also located on the back of the stereo.

Using the Phillips #0 Screwdriver, unscrew the 1 gold screw (length - 9.3mm), located on the bottom of a hole as noted in pictures (2) and (3).

Step 7

• Carefully pull the fuse out of the back of the stereo.

Carefully pull the fuse out of the back of the stereo.

Step 8

• Firmly grip the body of the stereo and pull off the silver back plate.

Firmly grip the body of the stereo and pull off the silver back plate.

Step 9

• Using the Phillips #0 Screwdriver, unscrew the 4 dark-silver screws (length - 3.71mm).

Using the Phillips #0 Screwdriver, unscrew the 4 dark-silver screws (length - 3.71mm).

Step 10

• Using the Phillips #0 Screwdriver, unscrew the 2 gold screws (length - 7.34mm) found on both sides of the stereo.

Using the Phillips #0 Screwdriver, unscrew the 2 gold screws (length - 7.34mm) found on both sides of the stereo.

Step 11

• Grip the top portion of the stereo, where the CD-Drive is located, and gently pull up to release it, but you will not be able to lift it all the way out.
• Grab the two tabs located near the back of the stereo, and gently pull the CD-drive front the rest of the device.

Grip the top portion of the stereo, where the CD-Drive is located, and gently pull up to release it, but you will not be able to lift it all the way out.

Grab the two tabs located near the back of the stereo, and gently pull the CD-drive front the rest of the device.

Step 12

              Power Supply               

• Remove the power supply on the circuit board. Please follow the iFixit soldering guide to assist you.

Remove the power supply on the circuit board. Please follow the iFixit soldering guide to assist you.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Chao Chen                     

Member since: 10/04/2011

79 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Cal Poly, Team 5-35, Amido Fall 2011                        

                                                  Member of Cal Poly, Team 5-35, Amido Fall 2011 



                    CPSU-AMIDO-F11S5G35                     


                                            4 Members                     


                                            8 Guides authored