Difficulty

Moderate

Steps

13

Time Required

                          3 - 6 minutes

Sections

2

  • SONY ZS-BTG900 Disassembly
  • 11 steps
  • Radio Adapter
  • 2 steps

Flags

0

  • BackSONY ZS-BTG900

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

If not, we are going to go ahead and open the device as you will need to swap out your radio adapter for a working one.

What you need

Step 1

              SONY ZS-BTG900 Disassembly
  • Lift up the handle to reveal the screws.
  • Use your Phillips #2 screwdriver to remove the eight 1/2 inch screws.

Lift up the handle to reveal the screws.

Use your Phillips #2 screwdriver to remove the eight 1/2 inch screws.

1024

Step 2

  • Flip your device over.
  • Use your Phillips #2 screwdriver to remove the six 3/4inch screws.
  • In removing the screws within the two holes on the back of the device, you may want to use your shaft extension to provide extra torque as they may be very tight.

Flip your device over.

Use your Phillips #2 screwdriver to remove the six 3/4inch screws.

In removing the screws within the two holes on the back of the device, you may want to use your shaft extension to provide extra torque as they may be very tight.

Step 3

  • Flip your device back over to access the top of the device.
  • Use your plastic opening tool to pry up and remove the panel on the top, left hand side of the device.
  • This will reveal two additional screws.

Flip your device back over to access the top of the device.

Use your plastic opening tool to pry up and remove the panel on the top, left hand side of the device.

This will reveal two additional screws.

Step 4

  • Use your Phillips #2 screwdriver to remove the two 1/2 inch screws underneath the now-removed panels.

Use your Phillips #2 screwdriver to remove the two 1/2 inch screws underneath the now-removed panels.

Step 5

  • Lift off the top, beginning from the back of the device.
  • Take care when lifting the top portion as there are many wires connected to the inside of the device and you do not want to disconnect these just yet.

Lift off the top, beginning from the back of the device.

Take care when lifting the top portion as there are many wires connected to the inside of the device and you do not want to disconnect these just yet.

Step 6

  • Disconnect the CD drive ribbon cable from the top of the device.

Disconnect the CD drive ribbon cable from the top of the device.

Step 7

  • Disconnect the antenna cables.

Disconnect the antenna cables.

Step 8

  • Disconnect the remaining cables from the motherboard.

Disconnect the remaining cables from the motherboard.

Step 9

  • Once you have removed the top, we will begin removing the front of the device.
  • Begin by disconnecting the 6 cables that lead from the front of the device to the motherboard.

Once you have removed the top, we will begin removing the front of the device.

Begin by disconnecting the 6 cables that lead from the front of the device to the motherboard.

Step 10

  • Use your Philips #2 screwdriver to remove the two 1 inch screws on the outermost part of the device.
  • Use your Philips #2 screwdriver to remove the two 3/4 inch screws on the outermost part of the device.
  • Use your Philips #2 screwdriver to remove the one 5/6 inch screw on the middle part of the device.

Use your Philips #2 screwdriver to remove the two 1 inch screws on the outermost part of the device.

Use your Philips #2 screwdriver to remove the two 3/4 inch screws on the outermost part of the device.

Use your Philips #2 screwdriver to remove the one 5/6 inch screw on the middle part of the device.

Step 11

  • Firmly pull off the front of device.
  • There will be a small amount of black glue. You can simply ignore this, and continue to pull, or use a sharp edge to cut the glue once you’ve revealed it.

Firmly pull off the front of device.

There will be a small amount of black glue. You can simply ignore this, and continue to pull, or use a sharp edge to cut the glue once you’ve revealed it.

Step 12

              Radio Adapter
  • Use a Phillips #2 screwdriver to unscrew the two 1/2 inch screws

Use a Phillips #2 screwdriver to unscrew the two 1/2 inch screws

Step 13

  • Lift and replace.
  • Disconnect white cable from motherboard.

Lift and replace.

Disconnect white cable from motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Alfredo Rodriguez

Member since: 04/11/2016

969 Reputation

                                      8 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges