Speaker Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          5 - 10 minutes            

Sections

4

• Battery
• 2 steps
• Front LCD Display
• 5 steps
• Inner LCD Display
• 4 steps
• Speaker
• 1 step

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

• BackNokia 6085h

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Flip over the phone so that the back is facing up.
• Pressing your thumb against the back cover, slide the cover off of the phone.

Flip over the phone so that the back is facing up.

Pressing your thumb against the back cover, slide the cover off of the phone.

1024

Step 2

• Remove the phone’s battery.

Remove the phone’s battery.

Step 3

              Front LCD Display               

• With the phone closed, run a plastic opening tool along the seam of the top half of the phone.
• Make sure to disconnect each of the five clips before proceeding to the next step.
• There are two clips on each side of the phone and one on the top.

With the phone closed, run a plastic opening tool along the seam of the top half of the phone.

Make sure to disconnect each of the five clips before proceeding to the next step.

There are two clips on each side of the phone and one on the top.

Step 4

• Remove the four 3.2 mm screws from the front panel using a T6 Torx screwdriver.
• The fourth screw is located under a fold in the ribbon cable.

Remove the four 3.2 mm screws from the front panel using a T6 Torx screwdriver.

The fourth screw is located under a fold in the ribbon cable.

Step 5

• Starting in the lower right corner, slowly begin to lift the tape that is holding down the front LCD and cables.
• Be careful around the two ribbon cables attached to the tape. These cables are fragile.
• Lift the tape from the board.

Starting in the lower right corner, slowly begin to lift the tape that is holding down the front LCD and cables.

Be careful around the two ribbon cables attached to the tape. These cables are fragile.

Lift the tape from the board.

Step 6

• Using a plastic opening tool, lift the ribbon cable connection below the front LCD.

Using a plastic opening tool, lift the ribbon cable connection below the front LCD.

Step 7

• Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board.

Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board.

Step 8

              Inner LCD Display               

• Locate the ribbon cable connection in the upper right hand corner of the board.
• Using a plastic opening tool, lift off the cable from the board.
• Be gentle and make sure not to rip the ribbon cable.

Locate the ribbon cable connection in the upper right hand corner of the board.

Using a plastic opening tool, lift off the cable from the board.

Be gentle and make sure not to rip the ribbon cable.

Step 9

• Using a plastic opening tool, slowly work the board off the mounts holding it to the frame.
• Flip the board over to reveal the main display.

Using a plastic opening tool, slowly work the board off the mounts holding it to the frame.

Flip the board over to reveal the main display.

Step 10

• Locate the ribbon cable for the main display on the bottom of the board.
• Slowly lift off the ribbon connector from its housing using a plastic opening tool.

Locate the ribbon cable for the main display on the bottom of the board.

Slowly lift off the ribbon connector from its housing using a plastic opening tool.

Step 11

• Slowly wedge the plastic opening tool under the bottom of the main display.
• Separate the display from the glue lifting it off the board.

Slowly wedge the plastic opening tool under the bottom of the main display.

Separate the display from the glue lifting it off the board.

Step 12

              Speaker               

• Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 6 other contributors 

                    Andrew                     

Member since: 10/04/2010

397 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Cal Poly, Team 4-46, Amido Fall 2010                        

                                                  Member of Cal Poly, Team 4-46, Amido Fall 2010 



                    CPSU-AMIDO-F10S4G46                     


                                            4 Members                     


                                            14 Guides authored