Difficulty
Easy
Steps
12
Time Required
Suggest a time??
Sections
2
- Cover
- 7 steps
- Gears
- 5 steps
Flags
0
BackStaples 34462 Electric Pencil Sharpener
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Cover
- Pull out the shavings tray from the pencil sharpener.
- Beware of loose pencil shavings falling on your workspace.
Pull out the shavings tray from the pencil sharpener.
Beware of loose pencil shavings falling on your workspace.
1024
Step 2
- Turn the pencil sharpener on its side.
Turn the pencil sharpener on its side.
Step 3
- Using a Phillips00 screwdriver, remove the two front 11.6mm screws.
- Using the plastic opening tool, remove the back plastic feet.
- After removing the back plastic feet, using a Phillips 00 screwdriver, remove the two back 11.6mm screws.
- The hole is deeper than you may think. It may take some time to get the screwdriver to click in.
Using a Phillips00 screwdriver, remove the two front 11.6mm screws.
Using the plastic opening tool, remove the back plastic feet.
After removing the back plastic feet, using a Phillips 00 screwdriver, remove the two back 11.6mm screws.
The hole is deeper than you may think. It may take some time to get the screwdriver to click in.
Step 4
- Carefully pull apart the bottom panel from the top panel.
- Be careful not to pull too forcefully as the panels are connected by wires.
- Beware of pencil shavings falling out onto your workspace.
Carefully pull apart the bottom panel from the top panel.
Be careful not to pull too forcefully as the panels are connected by wires.
Beware of pencil shavings falling out onto your workspace.
Step 5
- Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.
Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.
Step 6
- Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.
Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.
Step 7
- Carefully pull the cover from the top panel and set it aside.
Carefully pull the cover from the top panel and set it aside.
Step 8
Gears
- Using a Philips 00 screwdriver, remove the six 9.87mm screws securing the gear housing.
Using a Philips 00 screwdriver, remove the six 9.87mm screws securing the gear housing.
Step 9
- Carefully pull apart the gear housing’s panels.
- The gears are lubricated by petroleum jelly.
Carefully pull apart the gear housing’s panels.
The gears are lubricated by petroleum jelly.
Step 10
- Gently pry the first gear out of the gear housing with a spudger.
- To ease reassembly, note the orientation of the gear as you pry it free.
Gently pry the first gear out of the gear housing with a spudger.
To ease reassembly, note the orientation of the gear as you pry it free.
Step 11
- Gently pry the second gear out of the gear housing with a spudger.
- To ease reassembly, note the orientation of the gear before you pry it free.
Gently pry the second gear out of the gear housing with a spudger.
To ease reassembly, note the orientation of the gear before you pry it free.
Step 12
- Gently pry the third gear out of the housing with a spudger.
- To ease reassembly, note the orientation of the gear as you pry it free.
Gently pry the third gear out of the housing with a spudger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Brian Eliason
Member since: 10/27/2014
373 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Eastern Washington University, Team 1-5, Carnegie Fall 2014
Member of Eastern Washington University, Team 1-5, Carnegie Fall 2014
EWU-CARNEGIE-F14S1G5
7 Members
6 Guides authored
krzynka - Sep 19, 2020
Reply
What about gears? Where do you get them? Mine just needs the gear from step 12 replaced.
