Difficulty

Moderate

Steps

13

Time Required

                          10 - 20 minutes

Sections

2

  • How to open the SteelSeries Nimbus+ Controller
  • 10 steps
  • Thumbsticks
  • 3 steps

Flags

0

  • BackSteelSeries Nimbus+

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the phone mount
  • Use your fingers to remove the phone mount by pulling it straight out of the controller.

Use your fingers to remove the phone mount by pulling it straight out of the controller.

1024

Step 2

              Remove the sticker
  • Use your fingers to remove the sticker located on the back cover of the Nimbus+.
  • If you have trouble removing the sticker heat an iOpener and apply it to the rear case for two minutes to loosen the adhesive underneath.

Use your fingers to remove the sticker located on the back cover of the Nimbus+.

If you have trouble removing the sticker heat an iOpener and apply it to the rear case for two minutes to loosen the adhesive underneath.

Step 3

              Unscrew the back cover
  • Use a Y1 Tri-point screwdriver to remove the five 9.1 mm-long screws securing the back cover.

Use a Y1 Tri-point screwdriver to remove the five 9.1 mm-long screws securing the back cover.

Step 4

              Insert an opening pick
  • The back cover is held in place by plastic clips.
  • Insert an opening pick into the gap between the front and back cover assembly at the outside of the right controller handle.

The back cover is held in place by plastic clips.

Insert an opening pick into the gap between the front and back cover assembly at the outside of the right controller handle.

Step 5

              Release the plastic clips
  • Slide the opening pick to the top of the controller to release the remaining plastic clips on the right edge.

Slide the opening pick to the top of the controller to release the remaining plastic clips on the right edge.

Step 6

              Insert an opening pick
  • Insert an opening pick into the gap between the front and back cover assembly at the outside of the left controller handle.

Insert an opening pick into the gap between the front and back cover assembly at the outside of the left controller handle.

Step 7

              Release the plastic clips
  • Slide the opening pick to the top of the controller to release the remaining plastic clips on the left edge.

Slide the opening pick to the top of the controller to release the remaining plastic clips on the left edge.

Step 8

              Unfold the back cover assembly
  • Carefully fold the back cover assembly to the top of the SteelSeries Nimbus+ and bring it in an 90 degree angle.
  • Do not try to remove the back cover assembly all the way yet! It is still connected to mainboard.

Carefully fold the back cover assembly to the top of the SteelSeries Nimbus+ and bring it in an 90 degree angle.

Do not try to remove the back cover assembly all the way yet! It is still connected to mainboard.

Step 9

              Disconnect the battery cable
  • Use a pair of blunt nose tweezers to disconnect the battery cable from the mainboard.

Use a pair of blunt nose tweezers to disconnect the battery cable from the mainboard.

Step 10

              Remove the back cover assembly
  • Remove the back cover assembly.

Remove the back cover assembly.

Step 11

              Unscrew the board
  • Use a Phillips screwdriver to remove the two 7.0 mm-long screws securing the board.

Use a Phillips screwdriver to remove the two 7.0 mm-long screws securing the board.

Step 12

              Disconnect the thumbstick board
  • Disconnect the thumbstick board by pulling it straight out its socket on the mainboard.

Disconnect the thumbstick board by pulling it straight out its socket on the mainboard.

Step 13

              Remove the board
  • Remove the board with the thumbsticks from the mainboard.

Remove the board with the thumbsticks from the mainboard.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Adriana Zwink

Member since: 12/18/2019

36,607 Reputation

                                      167 Guides authored                  



                       Badges:
                       34







                                                        +31 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Anne Taylor - Jan 12, 2023

Reply

how can we find a replacement board with the thumbsticks?