Difficulty

Easy

Steps

8

Time Required

                          5 minutes

Sections

3

  • Nameplate
  • 4 steps
  • Top cover
  • 2 steps
  • Sensor Assemby
  • 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSteelseries Rival 700 Gaming Mouse

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnect the mouse from your computer
  • To avoid electronically damaging either your computer or your mouse, unplug the usb cable from its socket.

To avoid electronically damaging either your computer or your mouse, unplug the usb cable from its socket.

1024

Step 2

              Disconnect the cable from the mouse
  • The Rival 700 mouse is a non wireless mouse. The micro-USB cable end is an elbow socket, secured by a plastic clip.
  • To disconnect the cable from the mouse, firmly press the plastic clip using your thumb

The Rival 700 mouse is a non wireless mouse. The micro-USB cable end is an elbow socket, secured by a plastic clip.

To disconnect the cable from the mouse, firmly press the plastic clip using your thumb

Step 3

              Nameplate removal
  • The original nameplate is a soft rubber one that can be removed just by pulling it softly out of its socket.
  • WARNING: When reassembling, if you’re using a custom nameplate that may not be as stretchable as the original one, insert it softly, and use a lime tool on the new part to avoid damaging the mouse socket.

The original nameplate is a soft rubber one that can be removed just by pulling it softly out of its socket.

WARNING: When reassembling, if you’re using a custom nameplate that may not be as stretchable as the original one, insert it softly, and use a lime tool on the new part to avoid damaging the mouse socket.

Step 4

              Nameplate printing
  • You will be able to download the 3D files to design a custom nameplate on the Steelseries website. The link is also provided in the part description.
  • On this picture, the original “RIVAL” nameplate will be replaced with a new one on which i just had my Twitch ID printed.
  • Be creative, use colored plastic, put logos and drawings on your mouse.

You will be able to download the 3D files to design a custom nameplate on the Steelseries website. The link is also provided in the part description.

On this picture, the original “RIVAL” nameplate will be replaced with a new one on which i just had my Twitch ID printed.

Be creative, use colored plastic, put logos and drawings on your mouse.

Step 5

              Top cover removal
  • Use both your index and thumb to gently pry the top cover out from the mouse.
  • This part is a thin plastic one which needs a certain amount of strength to be removed. Be careful not to break it.

Use both your index and thumb to gently pry the top cover out from the mouse.

This part is a thin plastic one which needs a certain amount of strength to be removed. Be careful not to break it.

Step 6

              Top cover replacement
  • Steelseries sells a set of two different covers to replace the original one, with a sweat-resistant one f.e.
  • Check the parts section for the purchase link.
  • On the left, you can see on the wide led slot that is used to color the Steelseries logo on your mouse.

Steelseries sells a set of two different covers to replace the original one, with a sweat-resistant one f.e.

Check the parts section for the purchase link.

On the left, you can see on the wide led slot that is used to color the Steelseries logo on your mouse.

Step 7

              Sensor screws
  • Use a Philips #0 screwdriver to remove the four screws that are keeping the mouse sensor assembly sealed.

Use a Philips #0 screwdriver to remove the four screws that are keeping the mouse sensor assembly sealed.

Step 8

              Sensor removal
  • Insert your thumb and index in the two mouse holes and gently pry the sensor assembly out from its socket.

Insert your thumb and index in the two mouse holes and gently pry the sensor assembly out from its socket.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor 


                    Vincent Monteil

Member since: 07/06/2013

6,843 Reputation

                                      19 Guides authored                  



                       Badges:
                       30







                                                        +27 more badges