Difficulty
Easy
Steps
7
Time Required
10 - 15 minutes
Sections
1
- The Tent Arm
- 7 steps
Flags
0
BackTent
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
The Tent Arm
- Steps 1 through 3 are for removal of the broken arm.
- At the top joint, there will be a nut in the back that is holding the screw in place.
- Use the wrench to hold the nut in place.
- Use the Phillips screwdriver to unscrew the screw.
Steps 1 through 3 are for removal of the broken arm.
At the top joint, there will be a nut in the back that is holding the screw in place.
Use the wrench to hold the nut in place.
Use the Phillips screwdriver to unscrew the screw.
1024
Step 2
- Repeat step 1 for the other two joints.
- There is no need to hold the nut with the wrench for the middle joint because this joint holds two arms together.
- The nut is in the middle of the two arms, so once you have loosened the screw, the black connector will come off.
- Hold the nut in place and finish unscrewing the screw.
Repeat step 1 for the other two joints.
There is no need to hold the nut with the wrench for the middle joint because this joint holds two arms together.
The nut is in the middle of the two arms, so once you have loosened the screw, the black connector will come off.
Hold the nut in place and finish unscrewing the screw.
Step 3
- Remove the arm(s), after all three joints are unscrewed.
Remove the arm(s), after all three joints are unscrewed.
Step 4
- Steps 4 through 7 are for arm replacement.
- Replace the new arm, starting at the top joint again.
- Place the screw through the hole and twist the nut on the backside of the screw.
- Hold the nut with the wrench while you screw the screw to make it tight.
Steps 4 through 7 are for arm replacement.
Replace the new arm, starting at the top joint again.
Place the screw through the hole and twist the nut on the backside of the screw.
Hold the nut with the wrench while you screw the screw to make it tight.
Step 5
- At the middle joint, place the screw through the hole in the black plastic connector and through the conjoining arms.
- Use the Phillips screwdriver to tighten the screw in place.
At the middle joint, place the screw through the hole in the black plastic connector and through the conjoining arms.
Use the Phillips screwdriver to tighten the screw in place.
Step 6
- Repeat step 4 for the bottom joint.
- Remember to use the wrench to hold the nut in place while you screw the screw back tightly.
Repeat step 4 for the bottom joint.
Remember to use the wrench to hold the nut in place while you screw the screw back tightly.
Step 7
- Replace the canopy top by attaching the Velcro pieces.
- Once all of the joints have been tightly screwed back in place, the tent should be ready to reuse again.
Replace the canopy top by attaching the Velcro pieces.
Once all of the joints have been tightly screwed back in place, the tent should be ready to reuse again.
After following these instructions in chronological order, the end result would be for the successful removal and replacement of an arm on a Straight Leg Canopy Tent.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Virginia Gonzalez
Member since: 01/28/2017
146 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
USF Sarasota-Manatee, Team 1-1, Stewart Spring 2017
Member of USF Sarasota-Manatee, Team 1-1, Stewart Spring 2017
USFSM-STEWART-S17S1G1
19 Members
17 Guides authored
MK604CB - Jul 7, 2018
Reply
where do you buy the leg from?
