Svp 5800 Back Casing Replacement Repair Guide

Difficulty

Difficult

Steps

9

Time Required

                          25 minutes            

Sections

4

• Strap Hook
• 1 step
• Front Casing
• 3 steps
• Top button Compartment
• 3 steps
• Back Casing
• 2 steps

Flags

0

• BackSVP Aqua 5800

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Strap Hook               

• Locate the two 3.5 mm screws on the side of the device.
• Apply pressure to the PH J000 philips head screwdriver and turn in a counter clockwise motion until the screw becomes loose enough to pull out.

Locate the two 3.5 mm screws on the side of the device.

Apply pressure to the PH J000 philips head screwdriver and turn in a counter clockwise motion until the screw becomes loose enough to pull out.

1024

Step 2

              Front Casing               

• Once you have properly removed the strap hook, locate the two 3 mm screws located on the opposite side of the strap hook.
• Refer to the prerequisite guide on removing the strap hook for instructions.
• Place the PH J000 phillips head screwdriver on the head of screw; apply pressure and turn in a counter clockwise motion until screws come loose.

Once you have properly removed the strap hook, locate the two 3 mm screws located on the opposite side of the strap hook.

Refer to the prerequisite guide on removing the strap hook for instructions.

Place the PH J000 phillips head screwdriver on the head of screw; apply pressure and turn in a counter clockwise motion until screws come loose.

Step 3

• Place the plastic opening tool on the crack between the front and back casings.
• Apply pressure by pulling down on the plastic opening tool to pry the case apart.

Place the plastic opening tool on the crack between the front and back casings.

Apply pressure by pulling down on the plastic opening tool to pry the case apart.

Step 4

• Wedge your fingers in the opening and slowly pull the front casing away from the bottom casing until it complete separates from the device.
• Using too much force in this step can damage your device.

Wedge your fingers in the opening and slowly pull the front casing away from the bottom casing until it complete separates from the device.

Using too much force in this step can damage your device.

Step 5

              Top button Compartment               

• Insert the flat end of wide metal spudger into the seam of the plastic buffer surrounding the buttons and pry it open.

Insert the flat end of wide metal spudger into the seam of the plastic buffer surrounding the buttons and pry it open.

Step 6

• Use A #00 Phillips head screwdriver and turn counterclockwise to remove the four indicated screws.
• Set the screws aside.

Use A #00 Phillips head screwdriver and turn counterclockwise to remove the four indicated screws.

Set the screws aside.

Step 7

• Apply pressure and turn counterclockwise to remove the indicated 2.5 mm screw.

Apply pressure and turn counterclockwise to remove the indicated 2.5 mm screw.

Step 8

              Back Casing               

• Locate the 2 mm screw that is next to the battery compartment.
• Using the PH J000 phillips head screwdriver, apply pressure to the screw head and turn in a counter clockwise motion until the screw is loose.
• You do not have to completely remove the 2 mm screw. To prevent losing the screw, you may leave it loosely in its place.

Locate the 2 mm screw that is next to the battery compartment.

Using the PH J000 phillips head screwdriver, apply pressure to the screw head and turn in a counter clockwise motion until the screw is loose.

You do not have to completely remove the 2 mm screw. To prevent losing the screw, you may leave it loosely in its place.

Step 9

• Slide the flat edge of the plastic opening tool between the inner casing and the back outer casing.
• Push up on the plastic opening tool so that the back casing starts to lift from the inner casing.
• Lifting the casing too far may result in damage. Lift the casing slowly.

Slide the flat edge of the plastic opening tool between the inner casing and the back outer casing.

Push up on the plastic opening tool so that the back casing starts to lift from the inner casing.

Lifting the casing too far may result in damage. Lift the casing slowly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Cheyenne Heinen                     

Member since: 03/07/2016

337 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Marist, Team 1-3, Laflen Spring 2016                        

                                                  Member of Marist, Team 1-3, Laflen Spring 2016 



                    MARS-LAFLEN-S16S1G3                     


                                            2 Members                     


                                            5 Guides authored