Difficulty

Moderate

Steps

6

Time Required

                          10 minutes

Sections

1

  • Camera
  • 6 steps

Flags

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackSwann Doorphone Video Intercom

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Camera
  • Flip the outdoor camera over so that the underside is facing up.
  • Remove the back cover by grabbing the sides of the camera and pulling towards your body.

Flip the outdoor camera over so that the underside is facing up.

Remove the back cover by grabbing the sides of the camera and pulling towards your body.

1024

Step 2

  • With the back cover of the outdoor camera off, press the first gray button, with blue wire underneath, down as shown in the picture.
  • While pressing the gray square button, remove the blue wire from the first opening under the button.
  • Be sure to remove the same color wire for the outdoor camera as was used for the indoor video intercom.

With the back cover of the outdoor camera off, press the first gray button, with blue wire underneath, down as shown in the picture.

While pressing the gray square button, remove the blue wire from the first opening under the button.

Be sure to remove the same color wire for the outdoor camera as was used for the indoor video intercom.

Step 3

  • Remove the other wires using the same steps as the blue wire.
  • Using the JIS #0 screwdriver, remove the 2mm screws from the back plate.
  • Remove the back plate by pulling the plate away from the device.

Remove the other wires using the same steps as the blue wire.

Using the JIS #0 screwdriver, remove the 2mm screws from the back plate.

Remove the back plate by pulling the plate away from the device.

Step 4

  • Using the JIS #0 screwdriver, remove the 1mm screws from behind the camera.

Using the JIS #0 screwdriver, remove the 1mm screws from behind the camera.

Step 5

  • Using one of the tweezers from the Precision Tweezers Set, gently place them around the wire connector attached to the camera.
  • Pull slowly in the direction of the cables until the connector is no longer attached.

Using one of the tweezers from the Precision Tweezers Set, gently place them around the wire connector attached to the camera.

Pull slowly in the direction of the cables until the connector is no longer attached.

Step 6

  • Remove the camera from the device.

Remove the camera from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Emily Stenke

Member since: 02/14/2018

555 Reputation

                                      4 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team S2-G4, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S2-G4, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S2G4                     


                                            4 Members                     


                                            5 Guides authored

Mahdi Arab - Dec 8, 2021

Reply

https://www.leso.ir/automatic-gate-opene…

آیفون تصویری

https://www.leso.ir/Video-Door-Phone-Sys…

مانیتور آیفون تصویری حافظه دار

https://www.roham-tech.ir/Video-Door-Pho…

cctvgram - Aug 15, 2022

Reply

فروشگاه دوربین مداربسته

cctvgram - Aug 16, 2022

Reply

چاپ بنر تسلیت