Swann Doorphone Video Intercom Doorbell Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Camera
6 steps
Doorbell
5 steps

Flags

BackSwann Doorphone Video Intercom
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Camera

Flip the outdoor camera over so that the underside is facing up.
Remove the back cover by grabbing the sides of the camera and pulling towards your body.

Flip the outdoor camera over so that the underside is facing up.

Remove the back cover by grabbing the sides of the camera and pulling towards your body.

1024

Step 2

With the back cover of the outdoor camera off, press the first gray button, with blue wire underneath, down as shown in the picture.
While pressing the gray square button, remove the blue wire from the first opening under the button.
Be sure to remove the same color wire for the outdoor camera as was used for the indoor video intercom.

With the back cover of the outdoor camera off, press the first gray button, with blue wire underneath, down as shown in the picture.

While pressing the gray square button, remove the blue wire from the first opening under the button.

Be sure to remove the same color wire for the outdoor camera as was used for the indoor video intercom.

Step 3

Remove the other wires using the same steps as the blue wire.
Using the JIS #0 screwdriver, remove the 2mm screws from the back plate.
Remove the back plate by pulling the plate away from the device.

Remove the other wires using the same steps as the blue wire.

Using the JIS #0 screwdriver, remove the 2mm screws from the back plate.

Remove the back plate by pulling the plate away from the device.

Step 4

Using the JIS #0 screwdriver, remove the 1mm screws from behind the camera.

Using the JIS #0 screwdriver, remove the 1mm screws from behind the camera.

Step 5

Using one of the tweezers from the Precision Tweezers Set, gently place them around the wire connector attached to the camera.
Pull slowly in the direction of the cables until the connector is no longer attached.

Using one of the tweezers from the Precision Tweezers Set, gently place them around the wire connector attached to the camera.

Pull slowly in the direction of the cables until the connector is no longer attached.

Step 6

Remove the camera from the device.

Remove the camera from the device.

Step 7

              Doorbell

Using your fingers, take hold of the wire connector attached to the main board
Pull slowly towards your body until the connector is no longer attached.

Using your fingers, take hold of the wire connector attached to the main board

Pull slowly towards your body until the connector is no longer attached.

Step 8

Using the JIS #0 screwdriver, remove the 2 mm screws diagonal from each other from the main board.

Using the JIS #0 screwdriver, remove the 2 mm screws diagonal from each other from the main board.

Step 9

Gently pull the main board away from the inside of the device and leave to the side.
The main board will still be attached to the device by a remaining set of wires, but do not need to be removed.

Gently pull the main board away from the inside of the device and leave to the side.

The main board will still be attached to the device by a remaining set of wires, but do not need to be removed.

Step 10

Using the JIS #0 screwdriver, remove the 1mm screws from each side of the doorbell spring-loaded cover-plate
While removing the second screw, hold down the cover-plate with your index finger to prevent the plate from springing out.

Using the JIS #0 screwdriver, remove the 1mm screws from each side of the doorbell spring-loaded cover-plate

While removing the second screw, hold down the cover-plate with your index finger to prevent the plate from springing out.

Step 11

Remove the black circular doorbell cover-plate.
Remove the metal circular doorbell button.

Remove the black circular doorbell cover-plate.

Remove the metal circular doorbell button.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Joseph Kelemen

Member since: 02/14/2018

227 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       USF Tampa, Team S2-G4, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S2-G4, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S2G4                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team