Difficulty

Difficult

Steps

9

Time Required

                          10 - 25 minutes

Sections

3

  • Back cover
  • 3 steps
  • CD Drive
  • 3 steps
  • Motherboard
  • 3 steps

Flags

2

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

  • BackSylvania SDVD9004

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back cover
  • Remove ten 7mm Phillips #0 screws.
  • Remove four 5mm Phillips #0 screws.

Remove ten 7mm Phillips #0 screws.

Remove four 5mm Phillips #0 screws.

1024

Step 2

  • Flip the device over.
  • Lift the top.

Flip the device over.

Lift the top.

Step 3

  • This guide uses incorrect tools. Use an ESD safe tool, such as a nylon spudger, to complete this step.

This guide uses incorrect tools. Use an ESD safe tool, such as a nylon spudger, to complete this step.

Step 4

              CD Drive
  • This guide uses incorrect tools. Use an ESD safe tool, such as a nylon spudger, to complete this step.
  • Wedge head lightly between drive and bottom of tab.
  • Repeat on both sides.
  • Gently pull out ribbon

Wedge head lightly between drive and bottom of tab.

Repeat on both sides.

Gently pull out ribbon

Step 5

  • Drive Removal
  • Use Philip’s screw driver to remove three 7 mm screws.
  • Rotate counter clockwise to loosen screws.

Drive Removal

Use Philip’s screw driver to remove three 7 mm screws.

Rotate counter clockwise to loosen screws.

Step 6

  • This guide uses incorrect tools. Use an ESD safe tool, such as a nylon spudger, to complete this step.
  • Follow the red and black cables to the motherboard point of attachment.
  • Use a Flat head screwdriver.
  • Place head of driver into the grove of plug and port.
  • Wedge on all sides evenly to work out plug slowly.
  • Remove small and large plugs.

Follow the red and black cables to the motherboard point of attachment.

Use a Flat head screwdriver.

Place head of driver into the grove of plug and port.

Wedge on all sides evenly to work out plug slowly.

Remove small and large plugs.

Step 7

              Motherboard
  • Remove Ribbon from Rear Panel
  • This guide uses incorrect tools. Use an ESD safe tool, such as a nylon spudger, to complete this step.

Remove Ribbon from Rear Panel

Step 8

  • Anchor screw removal
  • Use Philip’s head screwdriver
  • Place head of driver into screw on mother board.
  • Rotate counter clockwise
  • Remove all four screws

Anchor screw removal

Use Philip’s head screwdriver

Place head of driver into screw on mother board.

Rotate counter clockwise

Remove all four screws

Step 9

  • Lift motherboard to expose battery

Lift motherboard to expose battery

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Sarah Henry

Member since: 10/31/2016

417 Reputation

                                      4 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Baylor, Team 5-10, Williams Fall 2016                        

                                                  Member of Baylor, Team 5-10, Williams Fall 2016 



                    BU-WILLIAMS-F16S5G10                     


                                            2 Members                     


                                            5 Guides authored