Difficulty
Moderate
Steps
4
Time Required
Suggest a time??
Sections
2
- Front Grate
- 2 steps
- Charging Port
- 2 steps
Flags
1
Scenic Route
This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.
BackTaoTronics TT-SK06
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Grate
- To remove the front grate of the speaker grab a metal spudger and go to the back corner of the device where the front panel curves around the device. Insert the spudger and ply apart the corner until clips release from panel. Repeat for the other side of the grate. When all clips are released pull grate off from the front of device
- When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The metal spudger is great when you need serious prying power, but the regular black nylon spudger or a plastic opening tool should be used whenever possible.
To remove the front grate of the speaker grab a metal spudger and go to the back corner of the device where the front panel curves around the device. Insert the spudger and ply apart the corner until clips release from panel. Repeat for the other side of the grate. When all clips are released pull grate off from the front of device
When working with electronics, it’s important to choose a tool that’s ESD-safe to avoid accidental damage to the device. The metal spudger is great when you need serious prying power, but the regular black nylon spudger or a plastic opening tool should be used whenever possible.
1024
Step 2
- Grab two metal spudgers and insert one into the slit underneath the silver plating on the top of the device. Pry upward with the spudger until you unhook the two locks on the top. Repeat same step for the bottom of the device. When all four tabs are released, slide device out of the casing
- Use caution when working with the metal spudger, as it can potentially damage your device.
Grab two metal spudgers and insert one into the slit underneath the silver plating on the top of the device. Pry upward with the spudger until you unhook the two locks on the top. Repeat same step for the bottom of the device. When all four tabs are released, slide device out of the casing
Use caution when working with the metal spudger, as it can potentially damage your device.
Step 3
Charging Port
- Locate the slit on the back of the device and the board will be located there. Remove board from slit by using tweezers.
Locate the slit on the back of the device and the board will be located there. Remove board from slit by using tweezers.
Step 4
- Once board is removed, locate silver component on the board. This is the charging port. Remove the charging port. To put it back on the board you need to solder the component back onto the board.
Once board is removed, locate silver component on the board. This is the charging port. Remove the charging port. To put it back on the board you need to solder the component back onto the board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Niko Fabian
Member since: 03/06/2016
715 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team 5-7, Landers Spring 2016
Member of UMass Dartmouth, Team 5-7, Landers Spring 2016
UMASSD-LANDERS-S16S5G7
3 Members
5 Guides authored
Thorsten - Jun 22, 2017
Reply
Ich bin bis Schritt 3 gekommen und wollte das Gerät komplett zerlegen nach dem ich die hinteren 8 Schrauben auch heraus gedreht hatte aber beide Gehäuseteile ließen sich nicht trennen. Was kann ich tun ?
