Tdk Life On Record Trek Max A34 Motherboard Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Battery
5 steps
Large Speaker
9 steps
Small Speaker
8 steps
Motherboard
2 steps

Flags

BackTDK Life on Record Trek Max A34
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Flip your device upside down so the battery cover is facing upwards.
Using the Torx T6 screwdriver, remove all seven 6 mm Torx screws that are located along the perimeter of the battery cover.

Flip your device upside down so the battery cover is facing upwards.

Using the Torx T6 screwdriver, remove all seven 6 mm Torx screws that are located along the perimeter of the battery cover.

1024

Step 2

Use the metal spudger prying tool to gently pry off the battery cover.
The battery should now be exposed.

Use the metal spudger prying tool to gently pry off the battery cover.

The battery should now be exposed.

Step 3

Starting from where the wires are connected, gently pull the battery out of the device.

Starting from where the wires are connected, gently pull the battery out of the device.

Step 4

Unplug the battery from the device by detaching the wires at the white connection box.
Detaching the wires may require some force.
Be careful not to rip the wires out of the device or the battery.

Unplug the battery from the device by detaching the wires at the white connection box.

Detaching the wires may require some force.

Be careful not to rip the wires out of the device or the battery.

Step 5

The battery is now separated from the device and may be replaced with a new battery.

The battery is now separated from the device and may be replaced with a new battery.

Step 6

              Large Speaker

Turn over the device so the bottom is facing up. Remove the screws of the battery cover using the iFixit TR7 screwdriver.
Remove the battery cover by pulling up where the screws should go.

Turn over the device so the bottom is facing up. Remove the screws of the battery cover using the iFixit TR7 screwdriver.

Remove the battery cover by pulling up where the screws should go.

Step 7

Carefully unplug and remove the battery.
Use the metal spudger to pry off the rubber bumpers from the bottom of the speaker.

Carefully unplug and remove the battery.

Use the metal spudger to pry off the rubber bumpers from the bottom of the speaker.

Step 8

Use a Phillips #00 screwdriver to remove the screws that were underneath the rubber bumpers.
Remove the battery holder. Be sure to thread the exposed wires through the hole within the holder.

Use a Phillips #00 screwdriver to remove the screws that were underneath the rubber bumpers.

Remove the battery holder. Be sure to thread the exposed wires through the hole within the holder.

Step 9

Use a metal spudger to pry off the front and back mesh screens.
You may need to move the metal spudger along the edge of the screen to remove it more easily.

Use a metal spudger to pry off the front and back mesh screens.

You may need to move the metal spudger along the edge of the screen to remove it more easily.

Step 10

Turn the speaker back upright. Use the metal spudger to pry up the rubber cover to reveal the buttons underneath.

Turn the speaker back upright. Use the metal spudger to pry up the rubber cover to reveal the buttons underneath.

Step 11

Use a Phillips #00 screwdriver to remove the screws that hold the top cover in place.
Remove the top cover.

Use a Phillips #00 screwdriver to remove the screws that hold the top cover in place.

Remove the top cover.

Step 12

On the backside of the device, remove the screws using the Phillips #0 screwdriver.
Only the screws on the backside are needed to hold the frame together. Do not remove screws on the front.
Once the screws are removed, separate the two frame pieces.

On the backside of the device, remove the screws using the Phillips #0 screwdriver.

Only the screws on the backside are needed to hold the frame together. Do not remove screws on the front.

Once the screws are removed, separate the two frame pieces.

Step 13

Within the device, there is a single cable connecting the large speaker to the motherboard. Unplug this cable.

Within the device, there is a single cable connecting the large speaker to the motherboard. Unplug this cable.

Step 14

On the front of the device, use the Phillips #0 screwdriver to remove the four screws holding the speaker in.
Once the screws are removed, you are able to push the speaker out from behind.

On the front of the device, use the Phillips #0 screwdriver to remove the four screws holding the speaker in.

Once the screws are removed, you are able to push the speaker out from behind.

Step 15

              Small Speaker

Use a TR7 screwdriver to remove the screws from the battery cover located on the underside of the device.
Remove the battery cover.

Use a TR7 screwdriver to remove the screws from the battery cover located on the underside of the device.

Remove the battery cover.

Step 16

Unplug and remove the battery.
Use a metal spudger to pry off the rubber padding.

Unplug and remove the battery.

Use a metal spudger to pry off the rubber padding.

Step 17

Use a J00 screwdriver to unscrew the screws that are under the rubber pads.
Remove the battery holder and be sure to thread the wires through the hole within the part.

Use a J00 screwdriver to unscrew the screws that are under the rubber pads.

Remove the battery holder and be sure to thread the wires through the hole within the part.

Step 18

Use a metal spudger to pry off the front and back mesh screens.
You may need to move the metal spudger along the edge of the screen to remove it easier.

You may need to move the metal spudger along the edge of the screen to remove it easier.

Step 19

Use the a metal spudger to pry up the rubber cover on the top surface of the device.
Peel off the rubber cover to reveal the buttons and screws underneath.

Use the a metal spudger to pry up the rubber cover on the top surface of the device.

Peel off the rubber cover to reveal the buttons and screws underneath.

Step 20

Use a J00 screwdriver to unscrew the screws that hold the top cover in place.
Remove the top cover.

Use a J00 screwdriver to unscrew the screws that hold the top cover in place.

Step 21

On the backside of the device, unscrew the case screws with a J00 screwdriver.
Only the screws on the backside are needed to hold the frame together, do not remove screws on the front.
Once the screws are removed, separate the two frame pieces.

On the backside of the device, unscrew the case screws with a J00 screwdriver.

Only the screws on the backside are needed to hold the frame together, do not remove screws on the front.

Step 22

The following steps can be applied to either the left or the right speaker.
Use a J00 screwdriver to unscrew the four screws that secure the speaker.
The speaker should fall out naturally. If the speaker is stuck, use a plastic opening tool or a metal spudger to gently lift it out.
Desolder the black and red speaker wires.
Review the Desolder guide if you are unfamiliar with soldering.

The following steps can be applied to either the left or the right speaker.

Use a J00 screwdriver to unscrew the four screws that secure the speaker.

The speaker should fall out naturally. If the speaker is stuck, use a plastic opening tool or a metal spudger to gently lift it out.

Desolder the black and red speaker wires.

Review the Desolder guide if you are unfamiliar with soldering.

Step 23

              Motherboard

Carefully detach the 4 white rectangular clips from the motherboard.

Carefully detach the 4 white rectangular clips from the motherboard.

Step 24

Carefully remove the motherboard from the device.

Carefully remove the motherboard from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Marilyn Ho

Member since: 11/04/2019

211 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       IUPUI, Team S1-G3, Harley Fall 2019                        

                                                  Member of IUPUI, Team S1-G3, Harley Fall 2019 



                    IUPUI-HARLEY-F19S1G3                     


                                            3 Members                     


                                            2 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team