Technics Sl 1900 Turntable Disassembly Repair Guide

Difficulty

Easy

Steps

Time Required

                          1 hour

Sections

Technics SL-1900 Turntable Disassembly
7 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackTurntable
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

I decided to disassemble the device to check the condition of the grease in the tone arm lift mechanism. If the grease was hard, I would clean it off and apply new grease Fortunately for me, the grease was still fine.

Therefore, to fix the problem I simply shot some WD-40 into two key moving points, and that was sufficient to get the lift mechanism working again. This lubrication did not require any disassembly at all; however, since I went through all of the disassembly I figured, why not turn it into a guide?

What you need

Step 1

              Remove Cover, Platter and Cartridge

Remove the transparent cover from the turntable. It lifts straight up.
Remove the phono cartridge assembly from the tone arm. Unscrew the retaining collar to release the assembly and then pull the assembly off.
Remove the rubber platter cover from the turntable.
Remove the metal platter from the turntable. Insert a finger into each of the large holes, and pull straight up.

Remove the transparent cover from the turntable. It lifts straight up.

Remove the phono cartridge assembly from the tone arm. Unscrew the retaining collar to release the assembly and then pull the assembly off.

Remove the rubber platter cover from the turntable.

Remove the metal platter from the turntable. Insert a finger into each of the large holes, and pull straight up.

1024

Step 2

              Remove The Top Case

Remove 8 Phillips screws from the bottom of the turntable. This releases the plastic top of the turntable. You have to move the tone arm toward the center of the unit in order to remove the plastic case top. Set the case top aside.
When pulling up on the plastic top, take special care around the three platter speed control knobs, which are mostly hidden under a plastic cover in the lower right corner of the turntable. When you remove the case top, the three knobs will be rattling around underneath the plastic cover.

Remove 8 Phillips screws from the bottom of the turntable. This releases the plastic top of the turntable. You have to move the tone arm toward the center of the unit in order to remove the plastic case top. Set the case top aside.

When pulling up on the plastic top, take special care around the three platter speed control knobs, which are mostly hidden under a plastic cover in the lower right corner of the turntable. When you remove the case top, the three knobs will be rattling around underneath the plastic cover.

Step 3

              Remove Tone Arm Assembly

The tone arm assembly is held in place by three screws on top, and three long screws on the bottom.
Beginning on the bottom, remove the three long screws that secure the assembly from the bottom.
Remove the two marked screws at the base of the tone arm assembly.
Remove the rubber plug covering the third screw. Remove the hidden screw.

The tone arm assembly is held in place by three screws on top, and three long screws on the bottom.

Beginning on the bottom, remove the three long screws that secure the assembly from the bottom.

Remove the two marked screws at the base of the tone arm assembly.

Remove the rubber plug covering the third screw. Remove the hidden screw.

Step 4

              Detach Wires from Base

The tone arm is still connected to the base of the turntable by several wires.
The audio cables from the tone arm pass through a plastic stress relief collar where they exit the case. Pull this stress relief collar out of its slot in the case bottom.
Remove the screw securing the grounding wire to the large circuit board. Put the screw back in the hole in the circuit board, so it doesn’t get lost.
After detaching these wires, the tone arm assembly comes free from the base of the turntable.

The tone arm is still connected to the base of the turntable by several wires.

The audio cables from the tone arm pass through a plastic stress relief collar where they exit the case. Pull this stress relief collar out of its slot in the case bottom.

Remove the screw securing the grounding wire to the large circuit board. Put the screw back in the hole in the circuit board, so it doesn’t get lost.

After detaching these wires, the tone arm assembly comes free from the base of the turntable.

Step 5

              Inspect the Turntable Internals

Inspect the internals of the turntable. The unit base still contains the motor, the circuit board, and a bunch of complicated plastic parts.
The bottom of the tone arm base contains some springs, wires, and some delicate moving parts. If the grease around the moving parts has hardened, replace it to allow proper operation.

Inspect the internals of the turntable. The unit base still contains the motor, the circuit board, and a bunch of complicated plastic parts.

The bottom of the tone arm base contains some springs, wires, and some delicate moving parts. If the grease around the moving parts has hardened, replace it to allow proper operation.

Step 6

              Lubricate the Tone Arm Lifting Mechanism

If the grease still feels soft and greasy, but nothing happens when you raise the tone arm lever, shoot some spray lube from the top, into the moving pillars of the bar that raises and lowers the tone arm. I used WD-40.
After lubricating, work the mechanism by gently pushing and pulling on the bar that raises and lowers the tone arm, while moving the control lever for the tone arm.
If you are successful you should observe that the tone arm lift bar slowly rises and falls as you raise and lower the lift control.

If the grease still feels soft and greasy, but nothing happens when you raise the tone arm lever, shoot some spray lube from the top, into the moving pillars of the bar that raises and lowers the tone arm. I used WD-40.

After lubricating, work the mechanism by gently pushing and pulling on the bar that raises and lowers the tone arm, while moving the control lever for the tone arm.

If you are successful you should observe that the tone arm lift bar slowly rises and falls as you raise and lower the lift control.

Step 7

              Replace Knobs During Reassembly

When reassembling the unit, take special care to reseat the control knobs back onto their controls on the circuit board.
First, remove the small plastic cover holding the control knobs captive. From the bottom, release three plastic tabs indicated in red. Then slide the small plastic cover forward, to release the two plastic tabs indicated in yellow.
Reseat the control knobs back onto their metal posts.
Replace the small plastic cover by inserting the two tabs (yellow) and pushing down to reseat the three tabs (red).

When reassembling the unit, take special care to reseat the control knobs back onto their controls on the circuit board.

First, remove the small plastic cover holding the control knobs captive. From the bottom, release three plastic tabs indicated in red. Then slide the small plastic cover forward, to release the two plastic tabs indicated in yellow.

Reseat the control knobs back onto their metal posts.

Replace the small plastic cover by inserting the two tabs (yellow) and pushing down to reseat the three tabs (red).

To reassemble your device, follow the rest of these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    gordonhamachi

Member since: 12/20/2014

2,742 Reputation

                                      13 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Member-Contributed Guide#

Introduction#

What you need#

Member-Contributed Guide

Introduction

What you need