Difficulty
Easy
Steps
9
Time Required
2 minutes
Sections
2
- Back Cover
- 3 steps
- Backup Battery
- 6 steps
Flags
0
BackTexas Instruments TI-92
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- The first step to any repair operation is to remove the front cover.
- Grab the back of the calculator with one hand and the cover with the other.
- Pull the cover off from one of the sides for easy removal.
The first step to any repair operation is to remove the front cover.
Grab the back of the calculator with one hand and the cover with the other.
Pull the cover off from one of the sides for easy removal.
1024
Step 2
- Orientate the calculator with the top facing towards you.
- Slide the locking tab,found on the top part of the calculator, to the unlock position.
Orientate the calculator with the top facing towards you.
Slide the locking tab,found on the top part of the calculator, to the unlock position.
Step 3
- “Locking Tab”
- To remove the back cover, slide the cover away from the locking tab towards the bottom of the calculator until the cover no longer slides.
- Then with the front of the calculator facing down, pull up on the back cover.
- The calculator should now be orientated with the front facing down, as shown in picture 2.
“Locking Tab”
To remove the back cover, slide the cover away from the locking tab towards the bottom of the calculator until the cover no longer slides.
Then with the front of the calculator facing down, pull up on the back cover.
The calculator should now be orientated with the front facing down, as shown in picture 2.
Step 4
Backup Battery
- Before removing the backup battery make sure your AA batteries are installed so that there is no loss of information.
- Using a #00 Philip Screwdriver remove the 19mm screw located near the center of the back of the calculator on the panel with words “Test Access”
Before removing the backup battery make sure your AA batteries are installed so that there is no loss of information.
Using a #00 Philip Screwdriver remove the 19mm screw located near the center of the back of the calculator on the panel with words “Test Access”
Step 5
- Remove the screw and lift the panel to access battery.
Remove the screw and lift the panel to access battery.
Step 6
- The backup battery can now be seen underneath a small metal cover held by a screw.
- Using the same screwdriver, unscrew the 4.6mm screw located under the panel and left of the backup battery.
The backup battery can now be seen underneath a small metal cover held by a screw.
Using the same screwdriver, unscrew the 4.6mm screw located under the panel and left of the backup battery.
Step 7
- Remove the metal cover keeping the backup battery in place.
Remove the metal cover keeping the backup battery in place.
Step 8
- Use an Ipod Opening Tool or a similar tool to pull up on the right side of the backup battery.
- The battery should pop out of position.
Use an Ipod Opening Tool or a similar tool to pull up on the right side of the backup battery.
The battery should pop out of position.
Step 9
- After the battery has been tilted out of its socket, simply remove it with your hands.
After the battery has been tilted out of its socket, simply remove it with your hands.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Daniel Maldonado
Member since: 04/14/2010
198 Reputation
9 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team 15-51, Garner Spring 2010
Member of Cal Poly, Team 15-51, Garner Spring 2010
CPSU-GARNER-S10S15G51
5 Members
9 Guides authored
