Difficulty

Moderate

Steps

9

Time Required

                          10 - 15 minutes            

Sections

2

  • Top Cover
  • 7 steps
  • Claw
  • 2 steps

Flags

0

  • BackThe Claw

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Cover               
  • Place The Claw machine in the up-right position with the control knobs facing you.

Place The Claw machine in the up-right position with the control knobs facing you.

1024

Step 2

  • Turn The Claw machine upside-down placing the top cover on the surface of your work area.

Turn The Claw machine upside-down placing the top cover on the surface of your work area.

Step 3

  • Remove all ten 6mm phillips #1 screws underneath the top cover using your #1 phillips head screwdriver.
  • It is helpful to choose a clear, well lit work space. There are multiple tiny screws that are easy to lose.

Remove all ten 6mm phillips #1 screws underneath the top cover using your #1 phillips head screwdriver.

It is helpful to choose a clear, well lit work space. There are multiple tiny screws that are easy to lose.

Step 4

  • Turn The Claw machine back to the upright position with controls facing you.

Turn The Claw machine back to the upright position with controls facing you.

Step 5

  • Remove the top cover of The Claw machine.

Remove the top cover of The Claw machine.

Step 6

  • Remove the ten 6 mm phillips #1 screws from the top flange.

Remove the ten 6 mm phillips #1 screws from the top flange.

Step 7

  • Lift the flange upward and off to the side of the machine.
  • There is enough wire connecting the flange to the machine that you will not need to cut the wire. The flange can be moved off to the side of the machine while you are working.
  • Cutting or ripping out the wire will cause damage to the machine so try not to put much tension on the wire.

Lift the flange upward and off to the side of the machine.

There is enough wire connecting the flange to the machine that you will not need to cut the wire. The flange can be moved off to the side of the machine while you are working.

Cutting or ripping out the wire will cause damage to the machine so try not to put much tension on the wire.

Step 8

              Claw               
  • Once you have removed the top cover of the claw you can easily access the claw and you will see that the claw is attached by two small chains.
  • Locate the small rings that attach the chain to the plastic claw.

Once you have removed the top cover of the claw you can easily access the claw and you will see that the claw is attached by two small chains.

Locate the small rings that attach the chain to the plastic claw.

Step 9

  • Using the precision tweezers or small needle nose pliers, gently widen the small rings enough so that they can be removed from the claw.
  • Replace the claw one ring at a time. The chain needs to be attached to the new claw in the same configuration. One side of the chain opens the claw and the other side is just a hanging support.

Using the precision tweezers or small needle nose pliers, gently widen the small rings enough so that they can be removed from the claw.

Replace the claw one ring at a time. The chain needs to be attached to the new claw in the same configuration. One side of the chain opens the claw and the other side is just a hanging support.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    Alain Pierre                     

Member since: 03/22/2016

1,149 Reputation

                                      9 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       UMass Dartmouth, Team 4-8, Catania Spring 2016                        

                                                  Member of UMass Dartmouth, Team 4-8, Catania Spring 2016 



                    UMASSD-CATANIA-S16S4G8                     


                                            3 Members                     


                                            9 Guides authored                     

Oliver Chew - Jul 24, 2018

Reply

Where do I buy a new grabber thing

Michelle Bianchini - Aug 10, 2018

Reply

The 1st joystick that moves the claw forward and back doesn’t work.

Mira DIP - Apr 12, 2020

Reply

What if the chain won’t go down as it deep as it used to be?

Greg Sturges - Aug 27, 2020

Reply

Can you reconnect the white cord in picture above in step 6 connecting the claw on top and bottom

Kathellyn Da silva - Feb 9, 2021

Reply

My chain fell off and I dont know how to fix