Difficulty

Moderate

Steps

7

Time Required

                          20 minutes            

Sections

3

  • Back
  • 5 steps
  • Motherboard
  • 1 step
  • Screen
  • 1 step

Flags

0

  • BackTomTom VIA 1530 TM

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back               
  • Position the device so that the underside is facing up.
  • Tilt the EasyPort Mount slightly upward and rotate it counterclockwise 180 degrees from the initial position.
  • Firmly grab the EasyPort Mount and remove it.
  • If it does not dislodge easily, gently twist the EasyPort Mount, applying increasing pressure until it does.

Position the device so that the underside is facing up.

Tilt the EasyPort Mount slightly upward and rotate it counterclockwise 180 degrees from the initial position.

Firmly grab the EasyPort Mount and remove it.

If it does not dislodge easily, gently twist the EasyPort Mount, applying increasing pressure until it does.

1024

Step 2

  • Turn the device 180 degrees so the screw in the EasyPort Mount compartment is on top.
  • Remove the 2mm screw beneath the EasyPort Mount compartment with the Torx T-5 head Screwdriver.

Turn the device 180 degrees so the screw in the EasyPort Mount compartment is on top.

Remove the 2mm screw beneath the EasyPort Mount compartment with the Torx T-5 head Screwdriver.

Step 3

  • Flip the device over so that the screen is facing up.
  • Wedge the plastic opening tool between the top and bottom of the device’s frame, gently sliding it around the outside edge.
  • It may be easier to start at one of the corners.
  • The gold ribbon cable connecting the screen to the motherboard is fragile and tears easily.
  • This specific device’s ribbon cable is torn.

Flip the device over so that the screen is facing up.

Wedge the plastic opening tool between the top and bottom of the device’s frame, gently sliding it around the outside edge.

It may be easier to start at one of the corners.

The gold ribbon cable connecting the screen to the motherboard is fragile and tears easily.

This specific device’s ribbon cable is torn.

Step 4

  • Carefully slide the screen forward, revealing the lower portion of the motherboard.
  • Remove the 3.6mm screw using the JIS #00 Screwdriver.
  • Rotate the device 180 degrees, carefully slide back the screen, and remove the remaining two screws.

Carefully slide the screen forward, revealing the lower portion of the motherboard.

Remove the 3.6mm screw using the JIS #00 Screwdriver.

Rotate the device 180 degrees, carefully slide back the screen, and remove the remaining two screws.

Step 5

  • Disconnect the battery and speaker cables.
  • Unlatch the motherboard from the case.

Disconnect the battery and speaker cables.

Unlatch the motherboard from the case.

Step 6

              Motherboard               
  • Wedge a spudger between the white plastic latch and the black connection port, disconnecting the gold ribbon cable.
  • Slide the gold ribbon cable out of the port.

Wedge a spudger between the white plastic latch and the black connection port, disconnecting the gold ribbon cable.

Slide the gold ribbon cable out of the port.

Step 7

              Screen               
  • Use a plastic opening tool to unlatch the screen from its case.
  • We recommend starting on the side with the gold ribbon cable as the latches are more tricky.
  • Unlatch the screen corner by corner instead of an entire side at one time.
  • The tearing sound is the adhesive holding the screen to the case. It will re-stick when you put the screen together.

Use a plastic opening tool to unlatch the screen from its case.

We recommend starting on the side with the gold ribbon cable as the latches are more tricky.

Unlatch the screen corner by corner instead of an entire side at one time.

The tearing sound is the adhesive holding the screen to the case. It will re-stick when you put the screen together.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    Jennifer Zakaria                     

Member since: 01/18/2018

555 Reputation

                                      6 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       Cal Poly, Team S12-G2, Banghart Winter 2018                        

                                                  Member of Cal Poly, Team S12-G2, Banghart Winter 2018 



                    CPSU-BANGHART-W18S12G2                     


                                            3 Members                     


                                            6 Guides authored