Difficulty
Easy
Steps
12
Time Required
3 minutes
Sections
3
- Back Cover
- 4 steps
- Battery
- 4 steps
- SSD
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackToshiba CB35- B3340 Chromebook 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the 2 rubber foot pads from the bottom (opposite the hinge) with the small Plastic Opening tool.
Remove the 2 rubber foot pads from the bottom (opposite the hinge) with the small Plastic Opening tool.
1024
Step 2
- Remove the 10 7.1 mm screws using Phillips #1 screwdriver.
Remove the 10 7.1 mm screws using Phillips #1 screwdriver.
Step 3
- Loosen the back cover by using a plastic opening tool all the way around the device.
- There are areas all along the sides of the device that help aid in this.
- Be careful when prying, and go slow. The silver plastic frame around the dull gray plastic bottom is fragile and easily dented from prying pressure.
Loosen the back cover by using a plastic opening tool all the way around the device.
There are areas all along the sides of the device that help aid in this.
Be careful when prying, and go slow. The silver plastic frame around the dull gray plastic bottom is fragile and easily dented from prying pressure.
Step 4
- Remove the back cover by gently lifting up on one side of the device.
- The easiest side to lift up on is the one with the removed rubber foot pads.
Remove the back cover by gently lifting up on one side of the device.
The easiest side to lift up on is the one with the removed rubber foot pads.
Step 5
Battery
- Remove the tape holding the speaker wire to the battery on both sides using a small opening tool.
Remove the tape holding the speaker wire to the battery on both sides using a small opening tool.
Step 6
- Remove the 4 Phillips 3.2 mm screws holding the battery in place, with the Phillips #1 screwdriver.
Remove the 4 Phillips 3.2 mm screws holding the battery in place, with the Phillips #1 screwdriver.
Step 7
- To disconnect the wire from the mother board, gently press down with the flat end of Spudger and pull on the wire.
- Gently shaking the wire from left to right helps with the wire removal
To disconnect the wire from the mother board, gently press down with the flat end of Spudger and pull on the wire.
Gently shaking the wire from left to right helps with the wire removal
Step 8
- Remove the battery by gently pulling on the bottom corners.
- Be careful to move the battery’s wire under the speaker’s wire.
Remove the battery by gently pulling on the bottom corners.
Be careful to move the battery’s wire under the speaker’s wire.
Step 9
SSD
- Location of the SSD card
Location of the SSD card
Step 10
- Remove the Phillips 3.6 mm screw using a Phillips #1 screwdriver.
Remove the Phillips 3.6 mm screw using a Phillips #1 screwdriver.
Step 11
- Remove the yellow tape by slowly peeling it away at the bottom on the SSD.
Remove the yellow tape by slowly peeling it away at the bottom on the SSD.
Step 12
- Remove the SSD card from the motherboard by gently pulling up on the side where the screw originally was and out in the same direction.
Remove the SSD card from the motherboard by gently pulling up on the side where the screw originally was and out in the same direction.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Jillian Thomas
Member since: 10/14/2017
209 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
USF Tampa, Team S1-G121, Cagle Fall 2017
Member of USF Tampa, Team S1-G121, Cagle Fall 2017
USFT-CAGLE-F17S1G121
3 Members
14 Guides authored
