Difficulty
Moderate
Steps
9
Time Required
6 minutes
Sections
2
- Back Cover
- 5 steps
- Charging Port
- 4 steps
Flags
0
BackToshiba Chromebook 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove all external devices from the Toshiba Chromebook 2.
Remove all external devices from the Toshiba Chromebook 2.
1024
Step 2
- Close the Toshiba Chromebook 2 and turn it over so that the bottom of the laptop is facing upwards toward you with the lettering on the bottom facing right side up.
Close the Toshiba Chromebook 2 and turn it over so that the bottom of the laptop is facing upwards toward you with the lettering on the bottom facing right side up.
Step 3
- Remove the 8 visible Phillips 8.25 mm screws using the Phillips #0 screwdriver.
Remove the 8 visible Phillips 8.25 mm screws using the Phillips #0 screwdriver.
Step 4
- Remove 2 hidden Phillips 8.25 mm screws located underneath the rubber grips at the back (opposite the hinges) with the Phillips #0 screwdriver.
- The rubber grips are glued in place, so you’ll need to peel them up with a spudger or other pry tool.
Remove 2 hidden Phillips 8.25 mm screws located underneath the rubber grips at the back (opposite the hinges) with the Phillips #0 screwdriver.
The rubber grips are glued in place, so you’ll need to peel them up with a spudger or other pry tool.
Step 5
- Remove the back panel by pulling up on 2 adjacent corners.
Remove the back panel by pulling up on 2 adjacent corners.
Step 6
Charging Port
- The changing port is located on the left side of the computer, when flipped over and the back cover is taken off, the port will be in the top right corner.
- In order to access the port, the metal hinge in the top right corner must be lifted up.
The changing port is located on the left side of the computer, when flipped over and the back cover is taken off, the port will be in the top right corner.
In order to access the port, the metal hinge in the top right corner must be lifted up.
Step 7
- Pry the metal hinge up with the spudger tool by sticking the flat end under the bottom of the hinge and leverage it up.
- Open the hinge all the way until it is sticking straight up.
Pry the metal hinge up with the spudger tool by sticking the flat end under the bottom of the hinge and leverage it up.
Open the hinge all the way until it is sticking straight up.
Step 8
- Press down on the white clip with the pointed side of the spudger tool and softly pull the wires out of the socket by pulling horizontally away from the clip to disconnect the charging port from the motherboard.
Press down on the white clip with the pointed side of the spudger tool and softly pull the wires out of the socket by pulling horizontally away from the clip to disconnect the charging port from the motherboard.
Step 9
- Pull the charging port out by pulling up on the cable that connects the port to the motherboard.
Pull the charging port out by pulling up on the cable that connects the port to the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 3 other contributors
Jason Lomsdalen
Member since: 10/06/2016
389 Reputation
1 Guide authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 10-4, Livingston Fall 2016
Member of Cal Poly, Team 10-4, Livingston Fall 2016
CPSU-LIVINGSTON-F16S10G4
4 Members
11 Guides authored
Brian “Deminox” Preston - Sep 14, 2017
Reply
ok… but what’s the part for the charging port itself to replace??
Tim Nolte - May 20, 2019
Reply
The power port part # is either SIQDD0BUHAD000(shorter) or SIQDD0BUIAD000(longer) depending on which model you have.
