Toshiba Chromebook 2 Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes - 1 hour

Sections

Display
15 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

BackToshiba Chromebook 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display

If there is a crack on the outer case of the display so that the display is working properly, but there is distractions on the screen from the shattered case. In that case, the outer case can be easily replaced. It is just a matter of pulling the plastic case that’s stuck against the LED screen, and push the new case back in its place.

If there is a crack on the outer case of the display so that the display is working properly, but there is distractions on the screen from the shattered case. In that case, the outer case can be easily replaced. It is just a matter of pulling the plastic case that’s stuck against the LED screen, and push the new case back in its place.

1024

Step 2

• Shattered LED screen is when you push your finger against the screen, you see some kind of a rainbow effect around your finger. If the LED screen is shattered, it is unusable, and needs to be replaced with a new LED screen.

• Shattered LED screen is when you push your finger against the screen, you see some kind of a rainbow effect around your finger. If the LED screen is shattered, it is unusable, and needs to be replaced with a new LED screen.

Step 3

If the light coming out of the display is not bright enough, check the picture settings manually, and try to adjust sharpness, contrast, and brightness.

If the light coming out of the display is not bright enough, check the picture settings manually, and try to adjust sharpness, contrast, and brightness.

Step 4

• If setting the picture manually did not change the brightness, it simply means that the LED in the back of the LED screen have broke. That means a new LED screen is required.

• If setting the picture manually did not change the brightness, it simply means that the LED in the back of the LED screen have broke. That means a new LED screen is required.

Step 5

To replace your display screen you need to shut down the computer first.

To replace your display screen you need to shut down the computer first.

Step 6

In order to get to the screen assembly, you need to remove the screen bezel (plastic frame around the screen)

In order to get to the screen assembly, you need to remove the screen bezel (plastic frame around the screen)

Step 7

To remove the bezel, you need to unscrew two screws in the bottom of the front screen hiding behind screw covers.

To remove the bezel, you need to unscrew two screws in the bottom of the front screen hiding behind screw covers.

Step 8

Frist, remove the screw covers with a small hobby knife. Use a PH #0 (Philips screwdriver) to unscrew the couple of screws in the front screen bezel.

Frist, remove the screw covers with a small hobby knife. Use a PH #0 (Philips screwdriver) to unscrew the couple of screws in the front screen bezel.

Step 9

Once you are done with unscrewing, snap off the screen bezel. To do that, you need to reach your fingernails of both hands on the inside of the screen bezel in the left or right side of the screen, and gently lift up and out.

Once you are done with unscrewing, snap off the screen bezel. To do that, you need to reach your fingernails of both hands on the inside of the screen bezel in the left or right side of the screen, and gently lift up and out.

Step 10

You will hear a snapping sound. Work your way around the screen bezel.

You will hear a snapping sound. Work your way around the screen bezel.

Step 11

Once you take out the screen bezel, four screws mount the LED screen. Unscrew them, tilt the screen forward, and lay it on the keyboard exposing the backside of the screen.

Once you take out the screen bezel, four screws mount the LED screen. Unscrew them, tilt the screen forward, and lay it on the keyboard exposing the backside of the screen.

Step 12

Once you do that, you will see the screen has only one connector. Use the hobby knife to lift up the adhesive tape (Be careful not to cut it) Pull the adhesive tape back, and grab the back of the connector with both your fingers, and gently pull the connector back out. Now the screen is loose.

Once you do that, you will see the screen has only one connector. Use the hobby knife to lift up the adhesive tape (Be careful not to cut it) Pull the adhesive tape back, and grab the back of the connector with both your fingers, and gently pull the connector back out. Now the screen is loose.

Step 13

Put the new 13.3’ LED screen in its place and start by connecting the screen connector. Put the screen where it is supposed to be mounted at, and screw back the four screws that hold the screen.

Put the new 13.3’ LED screen in its place and start by connecting the screen connector. Put the screen where it is supposed to be mounted at, and screw back the four screws that hold the screen.

Step 14

Now it’s a matter of putting the screen bezel back by pushing it in to stay around the screen.

Now it’s a matter of putting the screen bezel back by pushing it in to stay around the screen.

Step 15

Finally, screw back the two screws on the bottom of the screen bezel, and cover them with the screws covers.

Finally, screw back the two screws on the bottom of the screen bezel, and cover them with the screws covers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      17 other people completed this guide.

Author

                                      with 4 other contributors

                    Marwan Aljohani

Member since: 10/01/2015

599 Reputation

                                      1 Guide authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       IUPUI, Team 1-3, Hagerty Fall 2015                        

                                                  Member of IUPUI, Team 1-3, Hagerty Fall 2015 



                    IUPUI-HAGERTY-F15S1G3                     


                                            5 Members                     


                                            7 Guides authored

Mechelle Leavitt - Jun 19, 2018

I completed this step by step and even though I knew it was to no avail. Upon my completion, it booted right up! Thank You Ifixit!!!!

Brian Todd - Jun 10, 2020

Thank you so much for the great description. I thought my Chromebook was dead in the water but the troubleshooting guide and instructions for the lcd screen was just what I needed. Even before I could get the bezel off completely the screen came alive. From now on I will call my CB “Lazarus” since it has “risen” from the dead.

Yuel Berhane 7e Kyrkskolan 7-9 - Nov 30, 2021

&&^& you so much it,s so bad

Action Shots#

Scenic Route#

Needs More Images#

Introduction#

What you need#

Team#