Difficulty

Easy

Steps

9

Time Required

                          15 minutes

Sections

2

  • Back Panel
  • 6 steps
  • Hard Drive
  • 3 steps

Flags

0

  • BackToshiba Dynabook T552-58G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Turn the Toshiba Dynabook T552-58G so that the back panel is facing you.

Turn the Toshiba Dynabook T552-58G so that the back panel is facing you.

1024

Step 2

  • Remove the 10 screws located on the back panel of the Toshiba Dynabook T552-58G using a PH 0 screwdriver.
  • Each screw will be 5.3 mm long.

Remove the 10 screws located on the back panel of the Toshiba Dynabook T552-58G using a PH 0 screwdriver.

Each screw will be 5.3 mm long.

Step 3

  • Remove the black screw using the J0 screwdriver. This is located by the top right foot of the device.
  • This will allow removal of the hard drive cover.
  • This screw will not come out of the hard drive cover.

Remove the black screw using the J0 screwdriver. This is located by the top right foot of the device.

This will allow removal of the hard drive cover.

This screw will not come out of the hard drive cover.

Step 4

  • Remove the single screw located below the hard drive using the J0 screwdriver. This screw is 5.3 mm long.

Remove the single screw located below the hard drive using the J0 screwdriver. This screw is 5.3 mm long.

Step 5

  • Remove two screws located diagonally from the bottom-left screw of the hard drive using a J0 screwdriver. The screw closest to the hard drive is 5.2 mm long and the screw farther away is 4.2 mm long.
  • Remove the screw located diagonally from the top right screw of the hard drive using a J0 screwdriver. This screw is 5.2 mm long.

Remove two screws located diagonally from the bottom-left screw of the hard drive using a J0 screwdriver. The screw closest to the hard drive is 5.2 mm long and the screw farther away is 4.2 mm long.

Remove the screw located diagonally from the top right screw of the hard drive using a J0 screwdriver. This screw is 5.2 mm long.

Step 6

  • Slowly lift the back panel away from the computer.
  • There should be some resistance.
  • Once lifted, carefully remove the back panel.

Slowly lift the back panel away from the computer.

There should be some resistance.

Once lifted, carefully remove the back panel.

Step 7

              Hard Drive
  • The hard drive is located in the under the L-shaped panel on the back of the computer.

The hard drive is located in the under the L-shaped panel on the back of the computer.

Step 8

  • Carefully push the hard drive to the left

Carefully push the hard drive to the left

Step 9

  • Gently lift the hard drive using your fingers.

Gently lift the hard drive using your fingers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Laney Pilkington

Member since: 01/31/2019

329 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Appalachian State University, Team S1-G3, Menagarishvili Spring 2019                        

                                                  Member of Appalachian State University, Team S1-G3, Menagarishvili Spring 2019 



                    APSU-MENAGARISHVILI-S19S1G3                     


                                            3 Members                     


                                            13 Guides authored