Toshiba Excite 10 At300 Rear Facing Camera Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          15 - 25 minutes

Sections

Back Panel
3 steps
Battery
2 steps
Rear-Facing Camera
5 steps

Flags

BackToshiba Excite 10 AT300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Remove SD Card

Remove the SD card from the SD card slot.

Remove the SD card from the SD card slot.

1024

Step 2

              Open the Tablet

Use the opening tool to separate the front and rear panels by slipping the tool underneath the screen edge and sliding it around the entire device.
Make sure you unclip all of the clips on the back panel, or pulling it off will be difficult and may damage the tablet.

Use the opening tool to separate the front and rear panels by slipping the tool underneath the screen edge and sliding it around the entire device.

Make sure you unclip all of the clips on the back panel, or pulling it off will be difficult and may damage the tablet.

Step 3

              Disconnect Speaker Wires

Remove the speaker cable from its socket by gripping both sides of the white connector piece with tweezers and pulling straight out.
Be careful not to rip the wires out of the white connector piece.

Remove the speaker cable from its socket by gripping both sides of the white connector piece with tweezers and pulling straight out.

Be careful not to rip the wires out of the white connector piece.

Step 4

              Remove Screws

Using a #00 Phillips screwdriver, remove the following screws:
Five 3mm Phillips #00 screws

Using a #00 Phillips screwdriver, remove the following screws:

Five 3mm Phillips #00 screws

Step 5

              Remove Battery Cable

Gently lift the battery, pulling away from the tab holding it in place at the bottom.
While holding the battery up, use a pair of tweezers to remove the battery cable from its connector.

Gently lift the battery, pulling away from the tab holding it in place at the bottom.

While holding the battery up, use a pair of tweezers to remove the battery cable from its connector.

Step 6

              Remove screw and yellow tape

Using a #00 Philips screwdriver, remove the screw attaching daughter board.
Remove the yellow tape using a pair of tweezers.

Using a #00 Philips screwdriver, remove the screw attaching daughter board.

Remove the yellow tape using a pair of tweezers.

Step 7

              Remove Ribbon Cable

Unlock the ribbon cable housing using tweezers and/or a spudger.
Gently pull the ribbon cable out of its housing using the tweezers or your hands.

Unlock the ribbon cable housing using tweezers and/or a spudger.

Gently pull the ribbon cable out of its housing using the tweezers or your hands.

Step 8

              Remove copper foil wires

Pull copper tape away from the back, keeping it connected to the green rear camera board.
Be careful not to rip the copper tape.

Pull copper tape away from the back, keeping it connected to the green rear camera board.

Be careful not to rip the copper tape.

Step 9

              Remove the daughter board

Using your hands remove daughter board by lifting it off of the tablet chassis. Flip it over and place it next to the tablet face-down.
Do not disconnect the red and black wires connecting it to the vibrating mechanism.

Using your hands remove daughter board by lifting it off of the tablet chassis. Flip it over and place it next to the tablet face-down.

Do not disconnect the red and black wires connecting it to the vibrating mechanism.

Step 10

Gently pinch the ribbon cable connector between two fingers or with tweezers and pull it straight outwards. The ribbon cable connector should disconnect and the camera can now be replaced.

Gently pinch the ribbon cable connector between two fingers or with tweezers and pull it straight outwards. The ribbon cable connector should disconnect and the camera can now be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Gus Holz

Member since: 10/09/2014

297 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 14-26, Maness Fall 2014                        

                                                  Member of Cal Poly, Team 14-26, Maness Fall 2014 



                    CPSU-MANESS-F14S14G26                     


                                            4 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team