Difficulty
Easy
Steps
13
Time Required
8 minutes
Sections
4
- Battery
- 3 steps
- Optical Drive
- 3 steps
- RAM
- 3 steps
- Keyboard
- 4 steps
Flags
2
Missed a Step
Oops! This guide is currently missing some important steps.
Better Introduction
Improve this guide by completing or revising its introduction.
BackToshiba Qosmio X775-3DV80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Turn your laptop over so the underside is facing up.
Turn your laptop over so the underside is facing up.
1024
Step 2
- Identify the two sliding locks on either side of the battery.
- Simultaneously slide both locks outward to release the battery.
Identify the two sliding locks on either side of the battery.
Simultaneously slide both locks outward to release the battery.
Step 3
- Pull the battery straight out of its slot to remove it.
Pull the battery straight out of its slot to remove it.
Step 4
Optical Drive
- Locate the optical drive retaining screw on the underside of the laptop.
Locate the optical drive retaining screw on the underside of the laptop.
Step 5
- Using a Phillips #00 screwdriver, remove the optical drive retaining screw.
Using a Phillips #00 screwdriver, remove the optical drive retaining screw.
Step 6
- Using your finger or a spudger, push the optical drive out of its compartment so you can grab it.
- Pull the optical drive out of its slot in the side of the laptop.
Using your finger or a spudger, push the optical drive out of its compartment so you can grab it.
Pull the optical drive out of its slot in the side of the laptop.
Step 7
RAM
- Loosen the single screw on the service panel by twisting counterclockwise with a Phillips #00 screwdriver.
- It is a captive screw that will remain attached to the service panel.
Loosen the single screw on the service panel by twisting counterclockwise with a Phillips #00 screwdriver.
It is a captive screw that will remain attached to the service panel.
Step 8
- Using a spudger or plastic opening tool, pry off the service panel.
Using a spudger or plastic opening tool, pry off the service panel.
Step 9
- Using your fingers, pull the retaining clips away from the RAM sticks.
- Pull the RAM sticks out of the slots.
Using your fingers, pull the retaining clips away from the RAM sticks.
Pull the RAM sticks out of the slots.
Step 10
Keyboard
- Using a Phillips #00 screwdriver, remove all the remaining fourteen screws from the bottom case of the laptop.
- The service panel should already be removed.
Using a Phillips #00 screwdriver, remove all the remaining fourteen screws from the bottom case of the laptop.
The service panel should already be removed.
Step 11
- Using a Phillips #00 screwdriver, remove the five screws under the service panel.
- Remove the retaining clip.
Using a Phillips #00 screwdriver, remove the five screws under the service panel.
Remove the retaining clip.
Step 12
- Using a spudger, pry the keyboard from the top panel of the laptop.
- Make sure to pry it off all around.
Using a spudger, pry the keyboard from the top panel of the laptop.
Make sure to pry it off all around.
Step 13
- Disconnect the two ribbon cables connecting the keyboard to the laptop.
- Unplug the connector on the bottom of the laptop.
Disconnect the two ribbon cables connecting the keyboard to the laptop.
Unplug the connector on the bottom of the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Jesse Adam Ory
Member since: 03/24/2019
745 Reputation
7 Guides authored
Badges:
4
+1 more badge
Team
UMass Dartmouth, Team S2-G1, Bailey Spring 2019
Member of UMass Dartmouth, Team S2-G1, Bailey Spring 2019
UMASSD-BAILEY-S19S2G1
4 Members
14 Guides authored
