Difficulty

Moderate

Steps

12

Time Required

Suggest a time??

Sections

3

  • Battery
  • 1 step
  • Keyboard
  • 3 steps
  • Bottom Cover
  • 8 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackToshiba Satellite e205

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • With the battery away from you, slide the locking clips out.
  • The left clip stays, the right clip is spring loaded.
  • Slide the battery away from you.

With the battery away from you, slide the locking clips out.

The left clip stays, the right clip is spring loaded.

Slide the battery away from you.

1024

Step 2

              Keyboard
  • Use a spudger to carefully pry up the keyboard screw cover.

Use a spudger to carefully pry up the keyboard screw cover.

Step 3

  • Remove the two screws securing the keyboard to the chassis.

Remove the two screws securing the keyboard to the chassis.

Step 4

  • Carefully tilt the keyboard towards you and release the ribbon cables.
  • Use a spudger if needed to release the latch. The latch slides out.
  • The keyboard is now free and can be set aside.

Carefully tilt the keyboard towards you and release the ribbon cables.

Use a spudger if needed to release the latch. The latch slides out.

The keyboard is now free and can be set aside.

Step 5

              Bottom Cover
  • Remove the five black screws
  • Remove the one silver screw

Remove the five black screws

Remove the one silver screw

Step 6

  • Flip the laptop over so the bottom is facing up.
  • Using a spudger, remove the seven rubber inserts.
  • The feet only go in one location on the bottom of the laptop, so save yourself some time and track where they go.

Flip the laptop over so the bottom is facing up.

Using a spudger, remove the seven rubber inserts.

The feet only go in one location on the bottom of the laptop, so save yourself some time and track where they go.

Step 7

  • Remove the six silver screws.
  • Remove the one black screw.

Remove the six silver screws.

Remove the one black screw.

Step 8

  • Stand the laptop up on end.
  • Remove the two rubber inserts from the back of the laptop. One insert is on each side of the laptop.

Stand the laptop up on end.

Remove the two rubber inserts from the back of the laptop. One insert is on each side of the laptop.

Step 9

  • Remove the two screews.

Remove the two screews.

Step 10

  • Carefully work a spudger in the crack at the back of the laptop and separate the small rubberized section from the bottom of the laptop.

Carefully work a spudger in the crack at the back of the laptop and separate the small rubberized section from the bottom of the laptop.

Step 11

  • Remove the four screws.
  • Disconnect the black wireless antenna lead.

Remove the four screws.

Disconnect the black wireless antenna lead.

Step 12

  • The bottom of the laptop is now ready to lift off.
  • Carefully work a spudger around the seam of the laptop separating the bottom from the rest of the laptop.
  • There is a data connection at the front of the laptop that needs to be disconnected.
  • Use a spuder to carefully disconnect the wire from the motherboard. Once this is free the bottom will come off.

The bottom of the laptop is now ready to lift off.

Carefully work a spudger around the seam of the laptop separating the bottom from the rest of the laptop.

There is a data connection at the front of the laptop that needs to be disconnected.

Use a spuder to carefully disconnect the wire from the motherboard. Once this is free the bottom will come off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Tyler

Member since: 06/19/2012

4,821 Reputation

                                      16 Guides authored                  



                       Badges:
                       25







                                                        +22 more badges

Team

                       TechForce                        

                                                  Member of TechForce 



                    Business                     


                                            2 Members                     


                                            25 Guides authored

Devin Olson - Mar 16, 2016

Reply

Step 11 is missing the step of removing the wire from the white pin just above the nuvoTon chip (black in color) this is located when moving diagonally left from the black wireless antenna lead (green circle) and the top left red circle containing one of the black screws. All descriptions of direction are based on the picture used in step 11.