Toshiba Satellite L305 S5946 Base Housing Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          20 - 30 minutes

Sections

Battery
3 steps
Hard Drive
3 steps
RAM
4 steps
Keyboard
6 steps
Base Housing
6 steps

Flags

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

BackToshiba Satellite L305-S5946
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Place the laptop upside-down with the display hinges facing away from you.

Place the laptop upside-down with the display hinges facing away from you.

1024

Step 2

Slide the latch for the left battery bay to the left.

Slide the latch for the left battery bay to the left.

Step 3

Slide the latch for the right battery bay to the right and hold.
Continue to hold the latch while using a plastic opening tool to lift and remove the battery bay cover.
Remove the battery.

Slide the latch for the right battery bay to the right and hold.

Continue to hold the latch while using a plastic opening tool to lift and remove the battery bay cover.

Remove the battery.

Step 4

              Hard Drive

Loosen the two captive screws on the bottom left corner of the hard drive using a Phillips #1 screwdriver until you hear a click.

Loosen the two captive screws on the bottom left corner of the hard drive using a Phillips #1 screwdriver until you hear a click.

Step 5

Lift the hard drive cover using a non-marring iFixit opening tool.
This will expose the hard drive.

Lift the hard drive cover using a non-marring iFixit opening tool.

This will expose the hard drive.

Step 6

Slide the hard drive to the left using your fingers.
Remove the hard drive by inserting an iFixit opening tool under the right side of the hard drive and carefully lifting it out.

Slide the hard drive to the left using your fingers.

Remove the hard drive by inserting an iFixit opening tool under the right side of the hard drive and carefully lifting it out.

Step 7

RAM

Using a Phillips #1 screwdriver, turn the screw on the RAM cover until you hear a click.
This is a captive panel screw and remains with the cover.

Using a Phillips #1 screwdriver, turn the screw on the RAM cover until you hear a click.

This is a captive panel screw and remains with the cover.

Step 8

Remove the RAM cover by inserting the plastic opening tool into the indent and lifting.

Remove the RAM cover by inserting the plastic opening tool into the indent and lifting.

Step 9

Push the white and silver retaining clips away from each side of the RAM card using your fingernails.
The RAM card should pop up at an angle.

Push the white and silver retaining clips away from each side of the RAM card using your fingernails.

The RAM card should pop up at an angle.

Step 10

Pull the RAM card away from the computer.
Repeat Steps 6 and 7 to remove the other RAM card that may be installed.

Pull the RAM card away from the computer.

Repeat Steps 6 and 7 to remove the other RAM card that may be installed.

Step 11

              Keyboard

Place the laptop right-side-up so the screen faces you.

Place the laptop right-side-up so the screen faces you.

Step 12

Remove the strip of plastic at the right furthermost edge of the keyboard using a plastic opening tool.
Insert the plastic opening tool at either end of the strip.
Lift upwards and proceed to the other end while repeating this lifting process every one to two inches.

Remove the strip of plastic at the right furthermost edge of the keyboard using a plastic opening tool.

Insert the plastic opening tool at either end of the strip.

Lift upwards and proceed to the other end while repeating this lifting process every one to two inches.

Step 13

CAUTION: do not allow hardware or debris into the CPU fan and duct.
Remove the two 3-mm screws at the top edge of the keyboard using a Phillips #00 screwdriver.
These are not captive panel screws and, once loosened, will be free to move about the assembly.

CAUTION: do not allow hardware or debris into the CPU fan and duct.

Remove the two 3-mm screws at the top edge of the keyboard using a Phillips #00 screwdriver.

These are not captive panel screws and, once loosened, will be free to move about the assembly.

Step 14

Pry the top of the keyboard loose from its casing using a plastic opening tool.

Pry the top of the keyboard loose from its casing using a plastic opening tool.

Step 15

Gently grasp the top of the keyboard and pull it up and toward the screen.
CAUTION: Pulling too hard could damage the black ribbon cable under the keyboard.

Gently grasp the top of the keyboard and pull it up and toward the screen.

CAUTION: Pulling too hard could damage the black ribbon cable under the keyboard.

Step 16

Gently push the two tabs locking the black ribbon cable.
To remove the black ribbon cable from the motherboard, slide the keyboard toward the screen.
You may now safely separate the keyboard from the laptop.

Gently push the two tabs locking the black ribbon cable.

To remove the black ribbon cable from the motherboard, slide the keyboard toward the screen.

You may now safely separate the keyboard from the laptop.

Step 17

              Base Housing

Step 18

For the following steps, use a Phillips #1 screwdriver.
Remove the twelve 6-mm screws that border the bottom of the laptop.
Remove the 6-mm screw located in the lower middle of the device.
Remove the three 3-mm screws located in the battery bay.
Remove the one 4-mm screw located near the RAM.

For the following steps, use a Phillips #1 screwdriver.

Remove the twelve 6-mm screws that border the bottom of the laptop.

Remove the 6-mm screw located in the lower middle of the device.

Remove the three 3-mm screws located in the battery bay.

Remove the one 4-mm screw located near the RAM.

Step 19

Step 20

CAUTION: do not allow hardware or debris into the CPU fan and duct.
Use a Phillips #1 screwdriver to remove the five 6-mm screws in the keyboard slot.
These are not captive panel screws and, once loosened, will be free to move about the assembly.

Use a Phillips #1 screwdriver to remove the five 6-mm screws in the keyboard slot.

Step 21

Lock the white ribbon cable into place by gently pulling on the two black tabs.
Remove the white ribbon cable by pulling it towards you.
Remove the connector that has the blue, red, black, and white wires using tweezers.

Lock the white ribbon cable into place by gently pulling on the two black tabs.

Remove the white ribbon cable by pulling it towards you.

Remove the connector that has the blue, red, black, and white wires using tweezers.

Step 22

Separate the laptop upper casing from the lower casing by using an opening tool around the sides of the case to pry it apart.

Separate the laptop upper casing from the lower casing by using an opening tool around the sides of the case to pry it apart.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 11 other contributors

                    Michael Erberich

Member since: 04/17/2013

130 Reputation

                                      9 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 3-49, Amido Spring 2013                        

                                                  Member of Cal Poly, Team 3-49, Amido Spring 2013 



                    CPSU-AMIDO-S13S3G49                     


                                            4 Members                     


                                            19 Guides authored

Scenic Route#

Introduction#

What you need#

Team#

Scenic Route

Introduction

What you need

Team