Difficulty
Moderate
Steps
8
Time Required
30 minutes - 1 hour
Sections
3
- Battery
- 1 step
- Keyboard
- 3 steps
- Motherboard
- 4 steps
Flags
0
BackToshiba Satellite L755D-S5150
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- After shutting down your laptop, turn your laptop over and click the left tab left, then pull the right tab right as you pull the battery out.
- This step should always be done before working on your laptop to minimize electrostatic shock.
After shutting down your laptop, turn your laptop over and click the left tab left, then pull the right tab right as you pull the battery out.
This step should always be done before working on your laptop to minimize electrostatic shock.
1024
Step 2
Keyboard
- Using the plastic opening tool carefully pry the plastic strip that sits at the top of the keyboard.
Using the plastic opening tool carefully pry the plastic strip that sits at the top of the keyboard.
Step 3
- Use the Phillips PH00 to unscrew the four 4mm screws that holds the keyboard in place.
- Using the plastic opening tool carefully pry your keyboard out without disturbing the cord underneath it.
Use the Phillips PH00 to unscrew the four 4mm screws that holds the keyboard in place.
Using the plastic opening tool carefully pry your keyboard out without disturbing the cord underneath it.
Step 4
- Remaining is the cord that connects the keyboard to the motherboard. Remove this cord after the tabs are pressed in that releases keyboard.
Remaining is the cord that connects the keyboard to the motherboard. Remove this cord after the tabs are pressed in that releases keyboard.
Step 5
Motherboard
- Using the Phillips PH00 screwdriver remove the three 4mm screws from the cover for the RAM.
- Use the Phillips PH00 to remove the one 4mm screw that holds the ODD.
- Slide the ODD outward.
- Removing the RAM is not necessary
- The ODD is also commonly referred to as a CD-ROM.
Using the Phillips PH00 screwdriver remove the three 4mm screws from the cover for the RAM.
Use the Phillips PH00 to remove the one 4mm screw that holds the ODD.
Slide the ODD outward.
Removing the RAM is not necessary
The ODD is also commonly referred to as a CD-ROM.
Step 6
- Use the Phillips PH00 screwdriver to remove one 4mm screw.
- Use the Phillips PH00 screwdriver to remove the two 3mm screws from the fan.
- The motherboard will be accessed from below the keyboard, therefore you will not need to take out the bottom of the laptop.
Use the Phillips PH00 screwdriver to remove one 4mm screw.
Use the Phillips PH00 screwdriver to remove the two 3mm screws from the fan.
The motherboard will be accessed from below the keyboard, therefore you will not need to take out the bottom of the laptop.
Step 7
- Use the Phillips PH00 to unscrew the fifteen 4mm screws holding down the motherboard.
Use the Phillips PH00 to unscrew the fifteen 4mm screws holding down the motherboard.
Step 8
- Lift the motherboard and disconnect the 4 pin connector on the bottom side.
Lift the motherboard and disconnect the 4 pin connector on the bottom side.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 6 other contributors
Shaheedah
Member since: 10/06/2016
276 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
USF Tampa, Team 2-5, Sullivan Fall 2016
Member of USF Tampa, Team 2-5, Sullivan Fall 2016
USFT-SULLIVAN-F16S2G5
4 Members
5 Guides authored
mouhmmad ghassan - Jun 18, 2017
Reply
This my laptop for now .
