Toshiba Satellite L855 S5119 Charger Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Battery
3 steps
Back Plate Removal
1 step
Optical Drive
2 steps
Hard Drive
1 step
Back Cover Removal
1 step
Charger Port
2 steps

Flags

BackToshiba Satellite L855-S5119
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn the laptop face down to expose the back.
Locate the battery.

Turn the laptop face down to expose the back.

Locate the battery.

1024

Step 2

Locate the battery latches. The battery latch mechanism can be compared to a door – The right latch, when pushed right, unlocks the battery, while the left latch, when pushed left, releases the battery, pushing it out from its container.
Push the latch on the right to the right to unlock the battery latch locking mechanism.
Push the battery latch on the left to the left to unlock the battery.

Locate the battery latches. The battery latch mechanism can be compared to a door – The right latch, when pushed right, unlocks the battery, while the left latch, when pushed left, releases the battery, pushing it out from its container.

Push the latch on the right to the right to unlock the battery latch locking mechanism.

Push the battery latch on the left to the left to unlock the battery.

Step 3

With the left battery latch pushed left, remove the battery from its port by lifting the battery from the middle of the battery.
The battery will come free.

With the left battery latch pushed left, remove the battery from its port by lifting the battery from the middle of the battery.

The battery will come free.

Step 4

              Back Plate Removal

Turn the laptop over to place it top down.
Use a Phillips #1 screwdriver to remove the screw holding in the back plate. This screw does not come out of the plate.
Lift the back plate off the laptop, exposing the RAM and Hard Disk.

Turn the laptop over to place it top down.

Use a Phillips #1 screwdriver to remove the screw holding in the back plate. This screw does not come out of the plate.

Lift the back plate off the laptop, exposing the RAM and Hard Disk.

Step 5

              Optical Drive

Using a Phillips #0 screwdriver, remove the single 3mm screw.

Using a Phillips #0 screwdriver, remove the single 3mm screw.

Step 6

Rotate the laptop so that you have access to the optical drive.
The optical drive is now only attached by a port in the drive’s back. The optical drive can be pulled straight out of its housing.
Remove the drive.

Rotate the laptop so that you have access to the optical drive.

The optical drive is now only attached by a port in the drive’s back. The optical drive can be pulled straight out of its housing.

Remove the drive.

Step 7

              Hard Drive

Unscrew the hard drive.
There could be up to five 3mm screws - One on each corner of the hard drive, and one at one end of the hard drive, attaching the drive to the laptop’s frame.
Carefully push the hard drive away from its port. This should not require substantial force.
Lift the hard drive out.
Some hard drives have a plastic tab, which can be lifted from to remove the hard drive.
Otherwise, take hold of opposite sides of the hard drive and lift the drive straight up.

Unscrew the hard drive.

There could be up to five 3mm screws - One on each corner of the hard drive, and one at one end of the hard drive, attaching the drive to the laptop’s frame.

Carefully push the hard drive away from its port. This should not require substantial force.

Lift the hard drive out.

Some hard drives have a plastic tab, which can be lifted from to remove the hard drive.

Otherwise, take hold of opposite sides of the hard drive and lift the drive straight up.

Step 8

              Back Cover Removal

Unscrew the screws circled in red. This includes eleven 6mm screws, and one 5mm screw underneath where the optical drive was housed. All screws can be removed with a Phillips #0 screwdriver.
Carefully remove the back cover. The battery holder contains notches that help hold the case in place, so take care not to break those.

Unscrew the screws circled in red. This includes eleven 6mm screws, and one 5mm screw underneath where the optical drive was housed. All screws can be removed with a Phillips #0 screwdriver.

Carefully remove the back cover. The battery holder contains notches that help hold the case in place, so take care not to break those.

Step 9

              Charger Port

Locate the DC power port. Note the 4-pin connector attaching the port to the motherboard.

Locate the DC power port. Note the 4-pin connector attaching the port to the motherboard.

Step 10

Remove the 4 pin female connector from the male connector attached to the motherboard.
Lift the DC power port from the bracket holding it in place.
There are black plastic housings for the wires, holding the wires in position. Remove the red and black wires connecting the DC Port to the 4-pin power connector from underneath the black plastic housings.
Remove the DC Power port and 4 pin connector.

Remove the 4 pin female connector from the male connector attached to the motherboard.

Lift the DC power port from the bracket holding it in place.

There are black plastic housings for the wires, holding the wires in position. Remove the red and black wires connecting the DC Port to the 4-pin power connector from underneath the black plastic housings.

Remove the DC Power port and 4 pin connector.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Tyler Shafer

Member since: 02/12/2018

423 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Washington State, Team S1-G5, Lobnitz Spring 2018                        

                                                  Member of Washington State, Team S1-G5, Lobnitz Spring 2018 



                    WSU-LOBNITZ-S18S1G5                     


                                            4 Members                     


                                            9 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team