Difficulty
Difficult
Steps
24
Time Required
15 - 30 minutes
Sections
4
- Battery
- 2 steps
- Keyboard
- 6 steps
- CD/DVD Drive
- 4 steps
- Toshiba Satellite M305D-S4829 Motherboard Replacement
- 12 steps
Flags
0
BackToshiba Satellite M305D-S4829
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Unlatch the battery by pushing outward on both latches.
Unlatch the battery by pushing outward on both latches.
1024
Step 2
- Slide battery out.
Slide battery out.
Step 3
Keyboard
- Remove the five “F2” screws with a Phillips #0 screwdriver.
Remove the five “F2” screws with a Phillips #0 screwdriver.
Step 4
- Insert the plastic opening tool above the F1 key.
- Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.
Insert the plastic opening tool above the F1 key.
Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.
Step 5
- Find the screws above the F1 and INS keys.
- Unscrew both screws with a Phillips #0 screwdriver.
Find the screws above the F1 and INS keys.
Unscrew both screws with a Phillips #0 screwdriver.
Step 6
- Slowly lift the top edge of the keyboard out with your fingers.
- The ribbon cable located on the back of the keyboard will become accessible.
Slowly lift the top edge of the keyboard out with your fingers.
The ribbon cable located on the back of the keyboard will become accessible.
Step 7
- Locate the black ribbon cable flap.
- Detach flap with plastic opening tool. The ribbon cable will become free.
Locate the black ribbon cable flap.
Detach flap with plastic opening tool. The ribbon cable will become free.
Step 8
- Your keyboard has now been successfully removed.
Your keyboard has now been successfully removed.
Step 9
CD/DVD Drive
- Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.
Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.
Step 10
- Locate and remove the circled screw with a Phillips #0 screwdriver.
Locate and remove the circled screw with a Phillips #0 screwdriver.
Step 11
- Use the plastic opening tool to pry the CD/DVD drive out of the frame.
Use the plastic opening tool to pry the CD/DVD drive out of the frame.
Step 12
- Gently remove the CD/DVD drive from the laptop body.
Gently remove the CD/DVD drive from the laptop body.
Step 13
also remove these two screws
- Remove the circled screws with Phillips #0 screwdriver.
Remove the circled screws with Phillips #0 screwdriver.
Step 14
- Remove these screws from the underside of the laptop with Phillips #0 screwdriver.
Remove these screws from the underside of the laptop with Phillips #0 screwdriver.
Step 15
- Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.
- Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.
Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.
Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.
Step 16
- Remove the circled screw with a Phillips #0 screwdriver.
Remove the circled screw with a Phillips #0 screwdriver.
Step 17
- Detach the 3 marked cables by pulling them out with you fingers as shown.
- This may require some force. They do not come out easily.
Detach the 3 marked cables by pulling them out with you fingers as shown.
This may require some force. They do not come out easily.
Step 18
- Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.
Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.
Step 19
- Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.
Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.
Step 20
- Remove the circled motherboard screws with a Phillips #0 Scewdriver.
- Disconnect this ribbon cable.
Remove the circled motherboard screws with a Phillips #0 Scewdriver.
Disconnect this ribbon cable.
Step 21
- Remove these screws with a Phillips #0 screwdriver.
Remove these screws with a Phillips #0 screwdriver.
Step 22
- Detach the display cable by gently pulling it out with your fingers.
Detach the display cable by gently pulling it out with your fingers.
Step 23
- Remove the motherboard from the left side by gently lifting the left side upward.
- The boxed volume control may snag on the laptop frame when pulling the motherboard out.
Remove the motherboard from the left side by gently lifting the left side upward.
The boxed volume control may snag on the laptop frame when pulling the motherboard out.
Step 24
- The motherboard has now been removed from laptop.
The motherboard has now been removed from laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 7 other contributors
Michael Jensen
Member since: 04/18/2011
425 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 4-3, Regan Spring 2011
Member of Cal Poly, Team 4-3, Regan Spring 2011
CPSU-REGAN-S11S4G3
5 Members
6 Guides authored
