Turtle Beach Elite 800 Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 - 45 minutes

Sections

Ear Cushion
1 step
Audio Board
3 steps
Battery
1 step

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackTurtle Beach Elite 800
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Ear Cushion

To remove the ear cushions, press firmly down and rotate them clockwise, it should twist about 2mm and release, allowing you to pull it off.
When reassembling, be sure to line up the locking plates.

To remove the ear cushions, press firmly down and rotate them clockwise, it should twist about 2mm and release, allowing you to pull it off.

When reassembling, be sure to line up the locking plates.

1024

Step 2

              Audio Board

Remove the screws (9.47 mm Phillips head) from the blue plating on the headset to reveal the inside.

Remove the screws (9.47 mm Phillips head) from the blue plating on the headset to reveal the inside.

Step 3

If you are working on the LEFT side ear, you will first have to detach the battery by gently unplugging the white plug on the top of the board.
Make sure when unplugging the battery to not pull the manilla colored part which is attached to the board, but the white plug instead.
If you are working on the RIGHT side ear, you will first have to remove the charging contacts (2 7.92 mm Phillips screws).

If you are working on the LEFT side ear, you will first have to detach the battery by gently unplugging the white plug on the top of the board.

Make sure when unplugging the battery to not pull the manilla colored part which is attached to the board, but the white plug instead.

If you are working on the RIGHT side ear, you will first have to remove the charging contacts (2 7.92 mm Phillips screws).

Step 4

Desolder the necessary wires. (Each side will be slightly different.)
Be careful when using a soldering iron. Refer to the desoldering guide for tips.
For the purpose of this guide we clipped the wires connected to the board.
Remove the 4 screws (7.71mm Phillips head) using the #0 screw bit, that are holding the board in place.
Finally, remove the audio board.

Desolder the necessary wires. (Each side will be slightly different.)

Be careful when using a soldering iron. Refer to the desoldering guide for tips.

For the purpose of this guide we clipped the wires connected to the board.

Remove the 4 screws (7.71mm Phillips head) using the #0 screw bit, that are holding the board in place.

Finally, remove the audio board.

Step 5

              Battery

Remove the battery by carefully prying it from the headset.

Remove the battery by carefully prying it from the headset.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      12 other people completed this guide.

Author

                                      with 2 other contributors

                    Johnny Lofton

Member since: 01/18/2017

843 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Arkansas State University, Team 1-5, Chamberlain Spring 2017                        

                                                  Member of Arkansas State University, Team 1-5, Chamberlain Spring 2017 



                    ARSU-CHAMBERLAIN-S17S1G5                     


                                            3 Members                     


                                            10 Guides authored

Doug Green - Jul 20, 2017

So there are two batteries in this headset that need to be replaced?

Also, what battery do I purchase and does anyone know a good source to purchase them?

Dariusz Fukiet - Oct 19, 2017

Max battery size: 50x36x9mm

Origina battery: 40x30x8mm

The pcm board can be replacement by old battery module.

joze_markic_bf - Nov 7, 2017

Only one battery inside. Not sure why this guide takes appart the whole headset.

All steps&pictures related to right side (step 1, 2 and 4) are misleading and unnecessary when doing just battery replacement.

I ordered replacement on aliexpress.

jon fystro - Nov 7, 2017

What part number please and thank you in advance

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team