Difficulty
Very difficult
Steps
4
Time Required
30 minutes
Sections
1
- TVS Diode
- 4 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackUbiquiti UniFi AP AC Lite
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
In some cases, affected units’ center LEDs may flash dimly when the reset button is held pressed in with the POE power in place. This may only be visible if the board is out of it’s chassis.
The UAP-AC-LITE contains an over-voltage protection circuit driven by a unidirectional TVS diode. While this diode is not a fuse, it’s expected failure mode is to short, and divert power away from the rest of the board. This short is also detected by the PoE injector, which causes it to not deliver power.
In this guide will show how to:
- Disassemble the UAP-AC-LITETest if the over voltage protection TVS diode has failedRemove and replace the broken diode
What you need
Step 1
Open the UAP-AC-LITE
- The front cover is secured by 5 tabs.
- Work the Jimmy into the space near a clip, and create a big enough gap to insert a prying tool. Moderate pressure from a prying tool should force the clips open.
- There are a number of alignment tabs that can get in the way. It is best to try and work the Jimmy towards the center of the front cover, hugging its inside surface.
- The PCB is held down by 3 screws. It is not necessary to remove the board for this repair.
The front cover is secured by 5 tabs.
Work the Jimmy into the space near a clip, and create a big enough gap to insert a prying tool. Moderate pressure from a prying tool should force the clips open.
There are a number of alignment tabs that can get in the way. It is best to try and work the Jimmy towards the center of the front cover, hugging its inside surface.
The PCB is held down by 3 screws. It is not necessary to remove the board for this repair.
1024
Step 2
Test the TVS diode
- The TVS diode is located between the antenna and a large IC on the RJ45 port side of the board. It’s PCB marking is D6.
- It is a LittleFuse 24V uni-directional TVS diode, with J leads (SMBJ24A). Note the location of the white bar on the diode, which marks its orientation.
- Use a multimeter or ohmmeter to test that the diode has indeed shorted. A shorted diode will read less than 1 Ohm in both directions. A working diode will read significantly higher resistance in one direction relative to the other.
- If the diode is not shorted, then something else is wrong, and proceeding further may or may not help fix your access point.
The TVS diode is located between the antenna and a large IC on the RJ45 port side of the board. It’s PCB marking is D6.
It is a LittleFuse 24V uni-directional TVS diode, with J leads (SMBJ24A). Note the location of the white bar on the diode, which marks its orientation.
Use a multimeter or ohmmeter to test that the diode has indeed shorted. A shorted diode will read less than 1 Ohm in both directions. A working diode will read significantly higher resistance in one direction relative to the other.
If the diode is not shorted, then something else is wrong, and proceeding further may or may not help fix your access point.
Step 3
Remove the broken diode
- Desolder the broken diode. Apply heat to one lead while lifting the diode with tweezers. Once the solder melts the part should lift up. Repeat on the other lead.
- If the solder does not seem to melt, and the temperature is already plenty high, try using a bigger tip. Sometimes that helps to transfer more heat to the lead, melting the solder faster.
- Once the shorted diode is removed, the access point should power up and work as normal. However, omitting this part will potentially cause more damage if an over voltage event occurs.
Desolder the broken diode. Apply heat to one lead while lifting the diode with tweezers. Once the solder melts the part should lift up. Repeat on the other lead.
If the solder does not seem to melt, and the temperature is already plenty high, try using a bigger tip. Sometimes that helps to transfer more heat to the lead, melting the solder faster.
Once the shorted diode is removed, the access point should power up and work as normal. However, omitting this part will potentially cause more damage if an over voltage event occurs.
Step 4
Install new diode
- Make sure to test the new diode before installing it. A working TVS diode will show much higher resistance in one direction relative to the other.
- Install the new diode.
- Note the marking on the diode which indicates its orientation. The bar must be pointing towards the antenna.
- Apply flux to the pads, then add a thin layer of solder. If solder does not stick to the pads, you can add it to the underside of the diode pins instead.
- Hold the new diode in place using tweezers. While applying downward force, apply heat to one pin near the solder until the solder melts and makes a connection. Repeat with the other lead.
- Verify that the connections are good. There should be continuity between: one pin of D6 and a pin in VR3, and; the other pin of D6 and D7.
Make sure to test the new diode before installing it. A working TVS diode will show much higher resistance in one direction relative to the other.
Install the new diode.
Note the marking on the diode which indicates its orientation. The bar must be pointing towards the antenna.
Apply flux to the pads, then add a thin layer of solder. If solder does not stick to the pads, you can add it to the underside of the diode pins instead.
Hold the new diode in place using tweezers. While applying downward force, apply heat to one pin near the solder until the solder melts and makes a connection. Repeat with the other lead.
Verify that the connections are good. There should be continuity between: one pin of D6 and a pin in VR3, and; the other pin of D6 and D7.
To reassemble your device, reattach front cover.
Cancel: I did not complete this guide.
22 other people completed this guide.
Author
with 3 other contributors
Yang Zhao
Member since: 11/01/2016
801 Reputation
1 Guide authored
Badges:
7
+4 more badges
Maxime Rousseau - Oct 21, 2017
Reply
Do you think this problem has something to do with Ubiquiti dropping 24V devices altogether? I’ve read about the firmware problems that make 24V passive + POE switch setups a fire hazard, but do you think think this is a design choice or a fix for a flakey on-device power circuit?
Thanks for publishing this, I’ll give it a dead AP I have.
Maxime Rousseau - Oct 24, 2017
Mine broke in exactly the use case warned against here: https://community.ubnt.com/t5/UniFi-Wire…. This kind of failure definitely seems to be linked to the ‘accidental’ 48V activation issue. Unfortunately the device is OOW, but I’ll try to hit up Ubiquiti and see if I can get some good will.
effbees - Aug 22, 2018
Reply
Thank you! This fixed my Unifi AC Lite, I plugged it into a PoE switch that fried that diode.
Maya S. - Jun 30, 2019
Reply
Hi, can some help identify the corresponding Diode from this Tutorial on the Unifi UAP-AC-HD? Its POE sections is a little bigger. But didn’t find shorted Diodes. POE LED on Switch is on, but AP not powering on. It boots when 5 V are supplied manually, so somethings is wrong on the poe section.
https://i.imgur.com/WvljJ4T.jpg
It gets warm around the silver elko / capacity next to the transformator. But that’s all what I was able to figure out.
Roly - Jul 2, 2019
Reply
Good afternoon, if you were so kind to help me identify what the TVS diode is on this Unifi AC HD badge, thank you very much in advance!
