Difficulty
Moderate
Steps
9
Time Required
5 - 10 minutes
Sections
5
- Battery Cover
- 1 step
- Battery Pack
- 1 step
- Back Shell
- 3 steps
- Circuit Board
- 2 steps
- Home Button
- 2 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackUniden TCX905
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery Cover
- Starting from the top of the cover, slide down and away from the phone with your thumb
- Lift battery cover off of batter and place it to the side
Starting from the top of the cover, slide down and away from the phone with your thumb
Lift battery cover off of batter and place it to the side
1024
Step 2
Battery Pack
- Once battery cover is removed, place your thumb and index fingers on the the wires near the receptacle
- Gently pull straight up on the wires until a click is heard which signifies the battery is completely disconnected
- Place battery pack to the side
Once battery cover is removed, place your thumb and index fingers on the the wires near the receptacle
Gently pull straight up on the wires until a click is heard which signifies the battery is completely disconnected
Place battery pack to the side
Step 3
Back Shell
- Remove the two 11mm screws inside the battery storage compartment using Phillips #1 screwdriver (located near the very bottom of the phone)
Remove the two 11mm screws inside the battery storage compartment using Phillips #1 screwdriver (located near the very bottom of the phone)
Step 4
- Gently open phone casing along the seam at the bottom of the phone using index and middle fingers of both hands
Gently open phone casing along the seam at the bottom of the phone using index and middle fingers of both hands
Step 5
- Ensure that wired connection between circuit board and back shell is not strained
- Fold the back shell underneath the front shell and circuit board
Ensure that wired connection between circuit board and back shell is not strained
Fold the back shell underneath the front shell and circuit board
Step 6
Circuit Board
- Carefully remove the middle two 7mm screws, the outer top 9mm screws, and the top middle 7 mm screw that hold the logic board to the front shell of the phone casing using the Phillips #1 screwdriver
Carefully remove the middle two 7mm screws, the outer top 9mm screws, and the top middle 7 mm screw that hold the logic board to the front shell of the phone casing using the Phillips #1 screwdriver
Step 7
- Using index finger and thumb, carefully remove the circuit board from the front shell of phone
Using index finger and thumb, carefully remove the circuit board from the front shell of phone
Step 8
Home Button
- Remove the white plastic sheet covering the silicon button pad
- Remove the silicon button pad to access the home button and spring
- Note: Be mindful that the spring is small and sensitive and can be lost easily if not cautious
Remove the white plastic sheet covering the silicon button pad
Remove the silicon button pad to access the home button and spring
Note: Be mindful that the spring is small and sensitive and can be lost easily if not cautious
Step 9
- Once the silicon button pad is removed, remove the spring from home button
- Finally, remove the home button from its setting in the front shell of the phone
Once the silicon button pad is removed, remove the spring from home button
Finally, remove the home button from its setting in the front shell of the phone
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Gary Pence
Member since: 03/26/2014
807 Reputation
8 Guides authored
Badges:
8
+5 more badges
Team
Clemson, Team 1-1, Benson Spring 2014
Member of Clemson, Team 1-1, Benson Spring 2014
CLEM-BENSON-S14S1G1
3 Members
16 Guides authored
