Upgrade Iphone 12 64Gb Storage To 256Gb Repair Guide

Difficulty

Very difficult

Steps

8

Time Required

                          40 minutes            

Sections

1

• Upgrade iPhone 12 64GB Storage to 256GB
• 8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackiPhone 12

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Video Overview

Step 1

              Upgrade iPhone 12 64GB Storage to 256GB               

• The capacity of this iPhone is 64GB.
• Remove the display, Disconnect the battery, and Remove the motherboard.

The capacity of this iPhone is 64GB.

Remove the display, Disconnect the battery, and Remove the motherboard.

1024

Step 2

• Attach the motherboard to the holder and then attach the high-temperature tape.
• Heat the side of the NAND with Hot Air Gun at 280℃ and airflow 45.

Attach the motherboard to the holder and then attach the high-temperature tape.

Heat the side of the NAND with Hot Air Gun at 280℃ and airflow 45.

Step 3

• Remove black adhesive on the side of the NAND with a Side Glue Cleaner Blade.
• Heat the NAND with Hot Air Gun at 385℃ and airflow 45. Pry up the NAND with a Pry Knife
• Apply medium temperature solder paste to the bonding pad with Soldering Iron at 365℃.

Remove black adhesive on the side of the NAND with a Side Glue Cleaner Blade.

Heat the NAND with Hot Air Gun at 385℃ and airflow 45. Pry up the NAND with a Pry Knife

Apply medium temperature solder paste to the bonding pad with Soldering Iron at 365℃.

Step 4

• Apply a small amount of Paste Flux.
• Remove tin on the bonding pad with Soldering Iron and Solder Wick.
• Clean the bonding pad with PCB Cleaner.

Apply a small amount of Paste Flux.

Remove tin on the bonding pad with Soldering Iron and Solder Wick.

Clean the bonding pad with PCB Cleaner.

Step 5

• Heat the bonding pad with Hot Air Gun at 280℃ to remove the black adhesive.
• Dip rosin with Soldering Iron and Solder Wick to remove tin on the bonding pad.
• Clean the bonding pad with PCB Cleaner afterward.

Heat the bonding pad with Hot Air Gun at 280℃ to remove the black adhesive.

Dip rosin with Soldering Iron and Solder Wick to remove tin on the bonding pad.

Clean the bonding pad with PCB Cleaner afterward.

Step 6

• Apply some Paste Flux to the bonding pad and put an iPhone 12 256G NAND in position.
• Solder the NAND with Hot Air Gun at 365℃ and airflow 45.

Apply some Paste Flux to the bonding pad and put an iPhone 12 256G NAND in position.

Solder the NAND with Hot Air Gun at 365℃ and airflow 45.

Step 7

• Install the motherboard and display. Plug in the data cable and connect the iPhone to the computer. Open 3uTools to flash the iPhone.
• The phone does not display a progress bar during the flash process and won’t display a progress bar until the flash has finished.
• Activate the phone on 3uTools.

Install the motherboard and display. Plug in the data cable and connect the iPhone to the computer. Open 3uTools to flash the iPhone.

The phone does not display a progress bar during the flash process and won’t display a progress bar until the flash has finished.

Activate the phone on 3uTools.

Step 8

• Set up the phone and WiFi can be searched normally.
• Go to Settings > About. The phone has a 256G capacity.
• The serial number, WiFi address, and Bluetooth address remain unchanged.

Set up the phone and WiFi can be searched normally.

Go to Settings > About. The phone has a 256G capacity.

The serial number, WiFi address, and Bluetooth address remain unchanged.

It can be confirmed that the serial number, WiFi address, and Bluetooth address are no longer stored on the NAND. REWA technicians speculate that the serial number, WiFi address, and Bluetooth address are likely stored on EPROM or CPU. The technological change that Apple has made does make storage upgrade easier. But REWA doesn’t recommend that users upgrade storage on their own. The first reason is that Apple does not provide a warranty for the phone that has been disassembled before. The second reason is that inappropriate operation may lead to some malfunctions. The water resistance function will be much worse. But for a phone with a bad NAND, it will be much easier to repair.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    REWA                     

Member since: 11/24/2020

11,219 Reputation

                                      53 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges                           

Anwesh - Aug 4, 2022

Reply

will this work for iphone 12 pro?

Duck - Sep 12, 2022

If you have the right flash chip.