Difficulty
Easy
Steps
6
Time Required
15 minutes
Sections
2
- Charging Port
- 4 steps
- Speaker
- 2 steps
Flags
0
BackVerizon Ellipsis 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Charging Port
- Hold down the power button until the screen goes black to turn off the device.
- Remove the SIM card from the device to prevent damage.
- To remove the SIM card, open the SIM card cover on the side of the device.
- Push SIM card in and pull it out after hearing a click.
Hold down the power button until the screen goes black to turn off the device.
Remove the SIM card from the device to prevent damage.
To remove the SIM card, open the SIM card cover on the side of the device.
Push SIM card in and pull it out after hearing a click.
1024
Step 2
- Take off the back panel.
- Pry open the back cover carefully with a plastic opening tool.
- Use the opening tool to disconnect the cover completely. Do not attempt to pry the back cover off with your hands.
- Be sure to pry open all sides of the device. Attempting to take off the back cover when part of it is attached may snap the cover.
Take off the back panel.
Pry open the back cover carefully with a plastic opening tool.
Use the opening tool to disconnect the cover completely. Do not attempt to pry the back cover off with your hands.
Be sure to pry open all sides of the device. Attempting to take off the back cover when part of it is attached may snap the cover.
Step 3
- Remove the charging (micro-USB) port.
- Unscrew the indicated screws using the Phillips #00 screwdriver.
- The screws shown in the picture are the more common 4.76 mm.
- Disconnect the ribbon cable connecting the charging port board to the motherboard using tweezers.
- Use the tweezers to grab the sides of black, plastic connector. Do not grab from the wires or try to wedge it out from the bottom.
- Be extremely careful when disconnecting the ribbon cable. It is very delicate.
Remove the charging (micro-USB) port.
Unscrew the indicated screws using the Phillips #00 screwdriver.
The screws shown in the picture are the more common 4.76 mm.
Disconnect the ribbon cable connecting the charging port board to the motherboard using tweezers.
Use the tweezers to grab the sides of black, plastic connector. Do not grab from the wires or try to wedge it out from the bottom.
Be extremely careful when disconnecting the ribbon cable. It is very delicate.
Step 4
- Remove the charging port board from the phone using tweezers.
- Place the replacement charging port into the phone.
- Be cautious when replacing the ribbon cable onto the new charging port board.
Remove the charging port board from the phone using tweezers.
Place the replacement charging port into the phone.
Be cautious when replacing the ribbon cable onto the new charging port board.
Step 5
Speaker
- Remove 2 screws from each speaker, 4 screws in total, using a Phillips #00 screwdriver.
- The screws shown in the picture are the more common 4.76 mm.
Remove 2 screws from each speaker, 4 screws in total, using a Phillips #00 screwdriver.
Step 6
- Using tweezers carefully lift the connector up to disconnect it from the motherboard.
- Using tweezers carefully pull the speakers up and out of device.
Using tweezers carefully lift the connector up to disconnect it from the motherboard.
Using tweezers carefully pull the speakers up and out of device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 9 other contributors
Charles Gorbett
Member since: 10/10/2016
242 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
Sam Houston State, Team 12-7, Blackburne Fall 2016
Member of Sam Houston State, Team 12-7, Blackburne Fall 2016
SHSU-BLACKBURNE-F16S12G7
3 Members
10 Guides authored