Visual Land Prestige Elite 9Q Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          45 minutes - 1 hour

Sections

Battery
5 steps

Flags

BackVisual Land Prestige Elite 9Q
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Using the large plastic opening tool, start along a side of the device and apply light pressure in the seam between the top and bottom outer covers.
Maneuver the smaller plastic opening tool at the spot of the large opening tool and slowly slide along the edge.
You should feel each plastic connection begin to loosen.

Using the large plastic opening tool, start along a side of the device and apply light pressure in the seam between the top and bottom outer covers.

Maneuver the smaller plastic opening tool at the spot of the large opening tool and slowly slide along the edge.

You should feel each plastic connection begin to loosen.

1024

Step 2

Move tool around each connection, and continue around the device until all connections have been loosened.
The user risks damaging the connections if tool is slid to fast.

Move tool around each connection, and continue around the device until all connections have been loosened.

The user risks damaging the connections if tool is slid to fast.

Step 3

Once all connections have been loosened and using a soft surface, place the device onto its screen, and lift gently on the outer casing.
Open the casing and lay as shown keeping the speaker wires loose.

Once all connections have been loosened and using a soft surface, place the device onto its screen, and lift gently on the outer casing.

Open the casing and lay as shown keeping the speaker wires loose.

Step 4

Use wide tip tweezers to gently remove the three pieces of tape attached to battery.
Once the tape has been removed, the battery will be free from the tablet except for the wired connections to the circuit board.
Be careful not to severely damage the tape as this is what will hold the battery in place.
Mark where the positive (red) and negative (black) wires are on the circuit board.
Markings will be used for reassembly.

Use wide tip tweezers to gently remove the three pieces of tape attached to battery.

Once the tape has been removed, the battery will be free from the tablet except for the wired connections to the circuit board.

Be careful not to severely damage the tape as this is what will hold the battery in place.

Mark where the positive (red) and negative (black) wires are on the circuit board.

Markings will be used for reassembly.

Step 5

Before disconnecting battery, review Soldering Tips to ensure proper soldering.
Use soldering iron to remove +(red) battery lead.
Touch the positive wire to a metal surface acting as a ground to discharge the battery. Depending on the charge level of the battery, it may take up to 30 seconds to insure that it is fully discharged.
‘Ensure that the wires and solder do not touch each other, for this will damage the device
Remove the -(black) battery lead.
Remove and discard the old battery. Insert new battery and solder the positive and then the negative terminals to the circuit board.

Before disconnecting battery, review Soldering Tips to ensure proper soldering.

Use soldering iron to remove +(red) battery lead.

Touch the positive wire to a metal surface acting as a ground to discharge the battery. Depending on the charge level of the battery, it may take up to 30 seconds to insure that it is fully discharged.

‘Ensure that the wires and solder do not touch each other, for this will damage the device

Remove the -(black) battery lead.

Remove and discard the old battery. Insert new battery and solder the positive and then the negative terminals to the circuit board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    LAWRENCE SMITH

Member since: 07/19/2016

108 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       University of Memphis, Team 1-1, Kim SU 2016                        

                                                  Member of University of Memphis, Team 1-1, Kim SU 2016 



                    UM-KIM-SU16S1G1                     


                                            4 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team