Vtech Innotab 3S Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 25 minutes

Sections

Rear Panel
4 steps
Motherboard
2 steps
Screen
2 steps

Flags

BackVtech InnoTab 3S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Panel

While holding the battery compartment locks down, slide the two battery doors outwards from the sides of the device.
Remove the batteries from the device.

While holding the battery compartment locks down, slide the two battery doors outwards from the sides of the device.

Remove the batteries from the device.

1024

Step 2

Remove six 7 mm screws from the interior of the battery compartment using a Phillips #1 screwdriver.

Remove six 7 mm screws from the interior of the battery compartment using a Phillips #1 screwdriver.

Step 3

Using a nylon spudger, remove the five caps that hide the screws.
Potential for device damage: Be careful not to scrape the plastic from the device using the spudger.
When removing the caps, hold the spudger vertical to the board to make removal easier. Also try to push in with your spudger pointing towards the bottom of the device.
Remove the five 5 mm Phillips #1 screws from the rear panel of the device.

Using a nylon spudger, remove the five caps that hide the screws.

Potential for device damage: Be careful not to scrape the plastic from the device using the spudger.

When removing the caps, hold the spudger vertical to the board to make removal easier. Also try to push in with your spudger pointing towards the bottom of the device.

Remove the five 5 mm Phillips #1 screws from the rear panel of the device.

Step 4

Carefully remove the rear panel from the front panel of the device.
Once the rear panel is removed, you’ll be able to see the motherboard and other components within the Vtech InnoTab 3s.

Carefully remove the rear panel from the front panel of the device.

Once the rear panel is removed, you’ll be able to see the motherboard and other components within the Vtech InnoTab 3s.

Step 5

              Motherboard

Remove the six screws that secure the motherboard to the front panel of the device using a Phillips #1 screwdriver.
Remove the other 5mm screws that secure the charger port and the buttons to the inside of the front panel.
Remove the six 3 mm screws securing the battery clip.

Remove the six screws that secure the motherboard to the front panel of the device using a Phillips #1 screwdriver.

Remove the other 5mm screws that secure the charger port and the buttons to the inside of the front panel.

Remove the six 3 mm screws securing the battery clip.

Step 6

Using the tweezers, remove one battery clip from each corner (four total) of the Vtech InnoTab 3s.
With the tweezers, unsecure the charging port, headphone port, and the light switch button from the front panel of the device.
Potential for device damage: Avoid forceful movements when removing the motherboard to prevent damage of device components.

Using the tweezers, remove one battery clip from each corner (four total) of the Vtech InnoTab 3s.

With the tweezers, unsecure the charging port, headphone port, and the light switch button from the front panel of the device.

Potential for device damage: Avoid forceful movements when removing the motherboard to prevent damage of device components.

Step 7

              Screen

Open the clip holding the screen plug with the yellow film.
The clip securing the screen is located at the top of the motherboard.
Remove all seven of the 5mm screws on the motherboard to separate the motherboard from the screen.

Open the clip holding the screen plug with the yellow film.

The clip securing the screen is located at the top of the motherboard.

Remove all seven of the 5mm screws on the motherboard to separate the motherboard from the screen.

Step 8

Avoid forceful movements when separating the screen from the motherboard.
Carefully separate the motherboard from the device screen. Replace the damaged screen with an operational one.

Avoid forceful movements when separating the screen from the motherboard.

Carefully separate the motherboard from the device screen. Replace the damaged screen with an operational one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Karina Garcia

Member since: 08/30/2015

824 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       USF Tampa, Team 8-2, Eyestone Fall 2015                        

                                                  Member of USF Tampa, Team 8-2, Eyestone Fall 2015 



                    USFT-EYESTONE-F15S8G2                     


                                            4 Members                     


                                            9 Guides authored

david goodwin - Feb 22, 2016

What is the part number for the screen. Where can I buy one. Thank you.

Adrienne Dooms - Feb 26, 2016

what is the size of the screen

charma1963 - Jul 31, 2016

My grandson dropped his innotab 3 and now the screen is all scrambled. Can this be fixed? It did not crack the screen.

Michael Kurrus - Nov 8, 2016

Where can I buy the replacement screen for the Vtech innotab 3S

Introduction#

What you need#

Team#

Introduction

What you need

Team